manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 118

99

Glossary

The following table provides a list of commonly used DeviceNet terms.

Term

Explanation

Bus OFF

Indicates that the error rate in the network is extremely high. Errors are detected when a 
fixed threshold is exceeded by the internal error counter. (The internal error counter is 
cleared when the Master Unit is started or restarted.)

CAN

CAN is short for Controller Area Network. It is a communications protocol developed as a 
LAN for use in automobiles. DeviceNet employs CAN technology.

Configurator

A device for setting the system settings. The Configurator can read ID information, read 
and write parameters, and display the network configuration.

OMRON’s DeviceNet Configurator is designed for use with an OMRON Master Unit.

Consumed Connection Size

Indicates the data size (byte length) received via the connection.

ODVA

ODVA is short for Open DeviceNet Vendors Association, Inc. It is a non-profit organization 
formed by machine vendors with the aim to administer and popularize the DeviceNet 
specification.

Produced Connection Size

Indicates the data size (byte length) sent via the connection.

Connection

This is a logical communications channel for facilitating communications between nodes. 
Communications are maintained and managed between the master and slaves.

Device Profile

Standardizes the configuration and behavior (the smallest data configuration and opera-
tion that must be supported by the devices) of devices of the same type. Provides mutual 
exchangeability between devices of the same type. Also known as a device model. 
Devices for which device profiles are currently being studied include sensors, valves, dis-
play units, and encoders.

Master/Slave

A node can be either a master, which collects and distributes data, or a slave, which out-
puts and inputs data according to the instructions received from the master. OMRON’s 
DeviceNet products are already provided with either master or slave functions in a pre-
defined master/slave connection set. 

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands