Omron SMARTSLICE - 04-2008 Operation Manual Download Page 42

Page: 42 / 122

Unit Functions

Section 2-3

In the same way as above, click the

I/O Allocation (OUT)

Tab and edit the

I/O allocations. Set to block 1, allocated 3200.

Return to the General Tab Page and click

Download

Note

When

Auto allocation as is registered.

is selected in the General Tab Page,

each time the connection path is set, a message will be displayed indicating
that the current I/O allocations have been deleted because the connection
has been changed. To set the connection path, deselect

Auto allocation as is

registered.

before registering the Slaves.

2-3

Unit Functions

Function List

The following table lists the DeviceNet Communications Unit’s functions.

Function name

Summary

Setting/monitoring method

Table registration

Reads the configuration of the Slice I/O Units connected to the
Communications Unit and registers that information in a table.

Set with DIP switch.

Backup

Records the parameter data of all connected I/O Units in the Com-
munications Unit.

Set with DIP switch.

Automatic restore

Automatically downloads the backed-up parameter data to the
appropriate Unit.

Set with DIP switch.

Online replacement

I/O Units can be replaced without turning the power OFF.

No setting required.

Automatic baud rate
recognition

The Master's communications baud rate is automatically detected
and adopted.

No setting required.

Network power sup-
ply voltage monitor

The DeviceNet network's power supply voltage values are
recorded in the DeviceNet Communications Unit.

Set/read with Configurator or
explicit message.

Unit power ON time
monitor

Records the total time that the DeviceNet Communications Unit's
internal circuit power has been ON.

Set/read with Configurator or
explicit message.

Unit comment

A user-set name can be assigned to the Communications Unit.

Set/read with Configurator or
explicit message.

Network communi-
cations error history

A communications error history from the viewpoint of the Commu-
nications Unit can be collected in the Communications Unit.

Set/read with Configurator or
explicit message.

Summary of Contents for SMARTSLICE - 04-2008



























































































































Search results

Summary of Contents for SMARTSLICE - 04-2008

Reviews:

Brands by name

Popular brands

Omron SMARTSLICE - 04-2008, Operation Manual

Search results

Summary of Contents for SMARTSLICE - 04-2008

Reviews:

Brands by name

Popular brands