manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 18

xix

EC Directives

6

• When wiring or performing other tasks, do not allow metal objects such as

wire strands to enter the Unit.

• Always follow the electrical specifications for terminal polarity, communi-

cations path wiring, power supply wiring, and I/O jumpers. Incorrect wiring
can cause failures.

• Always wire the Unit as shown in the manual.

• Be sure to press terminals until they are fully seated.

• Mount Units only after checking terminal blocks completely.

• Be sure that the communications cable connectors and other items with

locking devices are properly locked into place.

• Do not drop the Unit or subject the Unit to excessive vibration or shock.

Doing so may cause malfunction or damage to the Unit. 

• Use the special packing box when transporting the Unit. Ensure that the

product is handled carefully so that no excessive vibration or impact is
applied to the product during transportation.

• Check the user program for proper execution before actually running it

with the system.

• Do not bend or pull the cables excessively.

• When connecting communications cables, always turn OFF the PLC

power supply, all Slave power supplies, and all communications power
supplies.

• Observe the following precautions when wiring the communications

cables.

• Wire the communications cables separately from the power lines or

high-tension lines.

• Do not bend the communications cables excessively.

• Do not pull on the communications cables excessively.

• Do not place objects on top of the communications cables.

• Route communications cables inside ducts.

• Always enable the scan list before operation.

• Before clearing the scan list of a Unit that has user-allocated remote I/O,

always confirm that no errors occur after the I/O Area setting is changed
to fixed allocation.

• When adding a new node to the network, check that the new node’s baud

rate is the same as the baud rate set on the other nodes.

• Do not extend connection distances beyond the ranges given in the spec-

ifications.

6

EC Directives

DeviceNet products conform to EMS and low-voltage level directives as fol-
lows:

EMC Directives

OMRON devices that comply with EC Directives also conform to the related
EMC standards, so that they can more easily be built in to other devices or the
overall machine. The actual products have been checked for conformity to
EMC standards. Whether they conform to the standards in the system used
by the customer, however, must be checked by the customer.

EMC-related performance of the OMRON devices that comply with EC Direc-
tives will vary depending on the configuration, wiring, and other conditions of

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands