Omron SMARTSLICE - 04-2008 Operation Manual Download Page 31

Page: 31 / 122

Nomenclature and Dimensions

Section 2-1

DeviceNet network status

Green

Unit is online with communications
established (normal network status).

Unit is online, but communications are
not established (waiting for communi-
cations from Master).

Red

Fatal communications error occurred.
(Network communications are not pos-
sible.)

• Node address duplicated
• Bus Off error

Non-fatal communications error
occurred.

• Communications timeout

---

Offline or power OFF

• Waiting for completion of node

address duplication check by Master.

• Power is not being supplied to the

DeviceNet Communications Unit.

Slice I/O Terminal com-
munications status

Green

Communicating with I/O Unit (commu-
nications established).

I/O Unit joining system.
(Flashing once every 1 s)

Backup/Restore function operating.
(Flashing once every 0.5 s)

• Restoring settings to I/O Unit, backup

function operating

• Downloading I/O Unit settings.

Red

Fatal communications error occurred.

Failure occurred while restoring set-
tings to I/O Unit or downloading I/O
Unit settings.
(Lit for 2 s)

Non-fatal communications error
occurred.

• Communications timeout
• Verification error occurred with regis-

tered table.

• Different model Unit detected after I/O

Unit replacement.

---

• Power not being supplied.
• Communications haven’t started with

I/O Unit.

• Overcurrent detected.

UNIT PWR

Unit power supply status

Green

24 V is being supplied to the Unit
power supply.

Unit power supply is OFF.

IOPWR

External I/O power sup-
ply status

Red

24 V is being supplied to the I/O power
supply.

I/O power supply is OFF.

Name

Color

Status

Meaning

Summary of Contents for SMARTSLICE - 04-2008



























































































































Search results

Summary of Contents for SMARTSLICE - 04-2008

Reviews:

Brands by name

Popular brands

Omron SMARTSLICE - 04-2008, Operation Manual

Search results

Summary of Contents for SMARTSLICE - 04-2008

Reviews:

Brands by name

Popular brands