![background image](http://html1.mh-extra.com/html/omron/cx-motion-ncf-v1-9/cx-motion-ncf-v1-9_operation-manual_744182126.webp)
102
Error Codes
Section 11-2
---
---
---
34
---
4022
Overrun limit
error
The motor exceeded the allow-
able motor operation range
that is set for the Overrun Limit
(Pn.026) for the position com-
mand input range.
---
---
---
---
34
@
The motor exceeded the allow-
able operation range that is set
for the Overrun Limit Setting
(Pn514) for the position com-
mand input.
---
---
---
36
36
@
4024
Parameter error
The data in the parameter save
area was corrupted when read-
ing data from EEPROM at
powering ON.
---
---
---
37
37
@
4025
Parameter Crash EEPROM write verification
data was corrupted when read-
ing data from EEPROM at
powering ON.
---
---
---
38
---
4026
Drive prohibit
input error
The positive and negative drive
prohibit inputs (NOT and POT)
were both ON when the Drive
Prohibit Input Selection
(Pn.004) was set to 0 and the
Stop Selection at Drive Prohibit
Input (Pn066) was set to 0 or 1.
Or, either the POT or NOT
input was ON when the Drive
Prohibit Input Selection
(Pn.004) was set to 2.
---
---
---
---
38
@
• The positive and negative
drive prohibit inputs (POT and
NOT) were both ON when the
Drive Prohibition Input Selec-
tion (Pn504) was set to 0.
• Either the POT or NOT input
was ON when the Drive Pro-
hibition Input Selection
(Pn504) was set to 2.
• An operation command (such
as for jogging) was executed
from the CX-Drive when the
Drive Prohibition Input Selec-
tion (PN504) was set to 0,
MECHATROLINK-II commu-
nications were disconnected,
and either the POT or NOT
input was ON.
• Either the POT or NOT input
was ON while an operation
command from the CX-Drive
was being executed.
---
---
A.28
---
---
No Code
(See note
1.)
Emergency stop
An emergency stop was input
during Servomotor operation.
Servo Drive display
Position
Control
Unit error
code
Error detection
function
Detected error or cause of
error
W
Series
W-series
(Built-in
Commu-
nica-
tions
Type)
SMART-
STEP Jun-
ior (Built-
in commu-
nications
Type)
G-Series
(Built-in
commu-
nica-
tions
Type)
G5-Series
(Built-in
commu-
nications
Type)
Summary of Contents for CX-MOTION-NCF - V1.9
