94
Error Codes
Section 11-2
Position
Control Unit
settings
and opera-
tions errors
Illegal oper-
ation
Multistart
error
0021
An operation com-
mand that cannot be
executed has been
sent to the Position
Control Unit.
The operation command that was sent can-
not be executed. Check the last command
timing and change the operation sequence.
Illegal data
Write trans-
fer error
0022
An attempt has been
made for the Position
Control Unit to write
data to an illegal
address, or to write
data using an illegal
data size.
The data transfer for the command cannot
be executed. Check the contents of the last
command, and correct the data transfer set-
tings.
Read trans-
fer error
0023
An attempt has been
made for the Position
Control Unit to read
data from an illegal
address, or to read
data with an illegal
data size.
The data transfer for the command cannot
be executed. Check the contents of the last
command, and correct the data transfer set-
tings.
FINS com-
mand time
monitor
error
0024
The cables between
the personal com-
puter and PLC have
been disconnected.
Reconnect the cables, and restart the Posi-
tion Control Unit.
The personal com-
puter’s operation is
slow.
Exit all other software and then restart the
Position Control Unit.
Transfer
cycle set-
ting error
0027
The set value for the
transfer cycle set in
the Position Control
Unit's Common
Parameters is too
small for the number
and type of con-
nected MECHA-
TROLINK devices or
the maximum axis
number.
Set and save a transfer cycle set value in
the Common Parameters that is suitable for
the number and type of connected MECHA-
TROLINK devices and the maximum axis
number, and then restart the Position Con-
trol Unit.
Initializa-
tion com-
mon
parameter
check error
0028
An illegal set value
has been detected in
the Common Param-
eters during Position
Control Unit initial-
ization.
When this error occurs, the corresponding
setting in the Common Parameters is set to
the default value (0). Execute ERROR
RESET, and then transfer and save the cor-
rect Common Parameter setting and restart
the Position Control Unit.
Data trans-
fer com-
mon
parameter
check error
0029
An illegal set value in
the Common Param-
eters was transferred
to the Position Con-
trol Unit using
WRITE DATA.
The transferred set value is discarded and
the set value in the Common Parameters
before the transfer is restored. Execute
ERROR RESET, and then transfer the cor-
rect Common Parameters setting.
Category
Error name Error code
Probable cause
Clearing method
Summary of Contents for CX-MOTION-NCF - V1.9
