manualshive.com logo in svg

OHAUS T72XW AM, Instruction Manual

Share
Download
OHAUS T72XW AM Instruction Manual Download Page 51

7000 SERIES INDICATORS 

EN 43 

 

 
Function Key 

 
The Function Key setup allows selection of the application that will be active when the 

FUNCTION

 key is pressed. 

Only one application can be selected. 
 
Assignment 
 
Options for the assignment of the 

FUNCTION

 key are: 

  Disabled (default) 

  Counting 

  Vehicle 

  Animal/Dynamic weighing 

  Checkweighing 

 

 
The next setup branches will vary based on the selection for the 

FUNCTION

 key assignment. Depending on the 

FUNCTION

 key selection, one of the following applications will be shown. If the 

FUNCTION

 key is disabled, none 

of the application setup branches will be shown and the next parameter will be the Reset function (refer to page 
45).  
 
For details on the setup, configuration and operation of each of these applications, please refer to Chapter 4, 
Applications: Configuration and Operation. 
 
Auto Start 
 
If the function key has been given an assignment, this parameter determines whether, when the indicator is 
powered on, the display will show the application. If Disabled, on startup the indicator will be in basic weighing 
mode. 

 
Animal/Dynamic weighing 

The following parameters are used to configure the Animal/Dynamic weighing application. 
 

 

Figure 3-12: Application Menu 

– Animal/Dynamic weighing 

 
 
 
 
 
 
 
 
 
 
 
 
 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for T72XW AM
















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands