Home
/
OHAUS
/
T72XW AM
/
Instruction Manual

OHAUS T72XW AM, Instruction Manual

Share

126 pages before
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143

Page: 141 / 143

OHAUS T72XW AM Instruction Manual Download Page 141

7000 SERIES INDICATORS

EN 133

LIMITED WARRANTY

OHAUS products are warranted against defects in materials and workmanship from the date of delivery through the
duration of the warranty period. During the warranty period OHAUS will repair, or, at its option, replace any
component(s) that proves to be defective at no charge, provided that the product is returned, freight prepaid, to
OHAUS.

This warranty does not apply if the product has been damaged by accident or misuse, exposed to radioactive or
corrosive materials, has foreign material penetrating to the inside of the product, or as a result of service or
modification by other than OHAUS. In lieu of a properly returned warranty registration card, the warranty period
shall begin on the date of shipment to the authorized dealer. No other express or implied warranty is given by
OHAUS Corporation. OHAUS Corporation shall not be liable for any consequential damages.

As warranty legislation differs from state to state and country to country, please contact OHAUS or your local
OHAUS dealer for further details.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

«
...
139
140
141
142
143
»

Summary of Contents for T72XW AM
















































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands