manualshive.com logo in svg

NXP Semiconductors MC9S12VRP64, Owner Reference Manual

Share
Download
NXP Semiconductors MC9S12VRP64 Owner Reference Manual Download Page 89

Port Integration Module (S12VRPPIMV1)

MC9S12VRP Family Reference Manual Rev. 1.3 

NXP Semiconductors

89

2.4.8.2

Analog Mode Operation

In analog mode (PTAENL=1) the input buffer is forced off (except if HVI test enabled, PTTEL=1, and not 
in direct mode PTADIRL=0). The voltage applied to a selectable HVI pin can be measured on its related 
ADC channel (refer to device overview information for channel assignment). One of two input divider 
ratios (Ratio

H_HVI

, Ratio

L_HVI

) can be chosen (PIRL) on the analog input or the voltage divider can be 

bypassed (PTADIRL=1). Additionally, in the latter case, the impedance converter in the ADC signal path 
can be used or bypassed in direct input mode (PTABYPL).

In run mode the digital input buffer of the selected pin is disabled to avoid shoot-through current unless 
PTTEL is set and PTDIRL is clear (the voltage divider is not bypassed). Thus pin interrupt can only be 
generated if PTTEL is set and PTDIRL is clear. 

In stop mode (RPM) the digital input buffer is enabled only if DIENL=1 to support wakeup functionality.

Table 2-42

 shows the HVI input configuration depending on register bits and operation mode.

2.5

Initialization and Application Information

2.5.1

Port Data and Data Direction Register writes

It is not recommended to write PORTx/PTx and DDRx in a word access. When changing the register pins 
from inputs to outputs, the data may have extra transitions during the write access. Initialize the port data 
register before enabling the outputs.

2.5.2

SCI Baud Rate Detection

The baud rate for SCI0 can be determined by using a timer channel to measure the data rate on the related 
RXD signal.

1. Establish the link: set MODRR2[MODRR27]=1 to route TIM1 input capture channel 1 to internal 

RXD0 signal of SCI0.

Table 2-42. HVI Input Configurations

Mode

DIENL

PTAENL

Digital Input

Analog Input

Resulting Function

Run

0

0

off

off

Input disabled (Reset state)

0

1

off

1

enabled

Analog input, interrupt not supported

1

0

enabled

off

Digital input, interrupt supported

1

1

off

1

1

Enabled if PTTEL=1 & PTADIRL=0)

enabled

Analog input, interrupt not supported

Stop

2

2

The term “stop mode” is limited to the voltage regulator operating in reduced performance mode (RPM) refer to “Low Power 
Modes” section in device overview. In any other case the HVI configuration defaults to “run mode”.

0

0

off

off

Input disabled, wakeup from stop not 
supported

0

1

off

off

1

0

enabled

off

Digital input, wakeup from stop supported

1

1

enabled

off

Summary of Contents for MC9S12VRP64












































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands