NEC Electra Elite 48/192 Features And Specifications Manual Download Page 476 | Manualshive

Page: 476 / 652

background image

Electa Elite

Issue 6

Features and Specifications Manual

P - 19

When the originating caller abandons the call, the user cannot enter
the call again.

Privacy Release cannot be activated again until both added stations
release the CO/PBX line.

A maximum of 16 Privacy Release calls are available.

Voice Over is prohibited to a station that has activated Privacy
Release.

When a station is receiving Voice Over, activating Privacy Release is
ignored and Voice Over continues.

Privacy Release and Live Record are not allowed at the same time.

Privacy Release cannot be used on Single Line Telephones.

Specified CO/PBX seizure cannot be used to activate Privacy
Release.

Privacy Release is not allowed when a conference is in progress.

To join a CO/PBX call using Privacy Release the originating CO/PBX
key or CAP key must be assigned to that station.

General:

Privacy Release can be activated or deactivated while a CO/PBX call
is in progress.

The red Conf LED flashes during Privacy Release. After Privacy
Release is canceled or all allowed parties have joined, the LED is off.

The Conf key LED indication for Privacy Release is the same as the
indication for a conference call.

When Privacy Release is activated, the Conf key LED winks on all
Multiline Terminals assigned to the same Tenant as the CO line with
Privacy Release, even when the CO line is assigned to multiple
Tenants.

When the Conf key is pressed from the same station that activated
Privacy Release, the Privacy Release feature is canceled.

Holding an internal call has priority over Privacy Release.

When a CO assigned as a private line is Privacy Released, the Conf
key at the shared private line flashes.

«
...
474
475
476
477
478
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: Samsung Pages: 7

Brand: Campbell Pages: 2

Brand: Hach Pages: 44

Brand: Habasit Pages: 14

Brand: LAUMAS Pages: 44

Brand: RayTek Pages: 2

Brand: Unify Pages: 144

Brand: UniData Communication Systems Pages: 60

Brand: UMBRA RIMORCHI Pages: 18

Brand: Vaisala Pages: 2

Brand: Panamorph Pages: 2

Brand: aci Pages: 8

BACnet / Modbus IMMERSION Series

Brand: aci Pages: 8

Brand: aci Pages: 4

Brand: Cobra Pages: 2

Brand: Celestron Pages: 24

Brand: Kasanova Pages: 22

Brand: Kask Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands