manualshive.com logo in svg

NEC Electra Elite 48/192, Features And Specifications Manual

The NEC Electra Elite 48/192 is a powerful and reliable communication system. Unlocking its full potential is made easy with the Features And Specifications Manual, a comprehensive guide to unleash the system's capabilities. Download this manual for free at manualshive.com to explore all the advanced features at your fingertips.

Share
Download
background image

Electra Elite                                                                                                                                

                  Issue 6

Features and Specifications Manual

D - 71

-OR-

When the 2-digit number is entered incorrectly, an error tone is heard
when chan is pressed. The LCD clears but the lock icon remains on as
the telephone goes into standby mode.   

 

SERVICE 
CONDITIONS

General:

Only one cordless terminal can be connected per ESI port.

Either cordless terminal can be used as a stand-alone device. 

Any cordless terminal can interface to every ESI port available in the
system. For D

term

 Cordless nine voice channels must be shared by

all D

term

 Cordless Terminals in the system. For D

term

 Cordless Lite,

up to 30 channels can be shared.

The D

term

 Cordless Terminal operating frequency ranges from

902.75 MHz to 925.70 MHz and the D

term

 Cordless Lite operates

from 902 MHz to 928 MHz. Both terminals share this frequency
range with other devices.  Interference or channel blockage could
occur from these other devices. 

Both terminal LCDs display DISCONNECT indicating the cordless
terminal is disconnected or the system is out of power.

The D

term

 Cordless Terminal LCD displays ICM HOLD when an

internal call is placed on hold. With the D

term

 Cordless Lite, pressing

the Hold key causes the associated function key to flash.

When there is no transmission between the base unit and the
handset for about five minutes, there are no LCD or LED indications
on the cordless terminal handset. Ringing off-hook or pressing keys
resumes LCD and LED indications.

A green LED is not provided with the cordless terminals. The LED
data for the green LED lights an LED on the cordless terminal.

Paging the other cordless terminal using the internal paging feature is
not recommended. The cordless terminal cannot answer an internal
page with Meet-Me when it is paged using internal paging.

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Zell AC1000 Operation Manual preview
AC1000
Brand: Zell Pages: 33
Panasonic KX-FLM551 Schematic Diagrams preview
KX-FLM551
Brand: Panasonic Pages: 2
Jabra GN 4170 Quick Setup Manual preview
GN 4170
Brand: Jabra Pages: 9
Jabra GN 4170 User Manual preview
GN 4170
Brand: Jabra Pages: 10
Jabra FREEWAY Datasheet preview
FREEWAY
Brand: Jabra Pages: 2
Jabra BT330 User Manual preview
BT330
Brand: Jabra Pages: 38
Paradox NV75M User & Installation Manual preview
NV75M
Brand: Paradox Pages: 2
Panther Panther II 1032 Quick Reference Manual preview
Panther II 1032
Brand: Panther Pages: 27
Uniden FP100 Operating Manual preview
FP100
Brand: Uniden Pages: 20
Raven Slingshot Installation Manual preview
Slingshot
Brand: Raven Pages: 70
YachtSafe W030 Manual preview
W030
Brand: YachtSafe Pages: 2
Barker 25895 Owner'S Instructions preview
25895
Brand: Barker Pages: 2
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Brand: OCTO Pages: 5
PCB Piezotronics IMI SENSORS EX640B61 Installation And Operating Manual preview
IMI SENSORS EX640B61
Brand: PCB Piezotronics Pages: 70
Takex DA-303S Instruction Manual preview
DA-303S
Brand: Takex Pages: 4
Guardian Telecom ACT-30 Installation & Operation Manual preview
ACT-30
Brand: Guardian Telecom Pages: 16
Lincoln Electric IM573 Calibration Information Manual preview
IM573
Brand: Lincoln Electric Pages: 32
Scitec AEGIS-5 Datasheet preview
AEGIS-5
Brand: Scitec Pages: 1

Brands by name

Popular brands

Load more brands