NEC Electra Elite 48/192 Features And Specifications Manual Download Page 139 | Manualshive

Page: 139 / 652

background image

C - 20

Caller ID Indication

(Analog Trunks)

Issue 6

Electra Elite

Using System Software S3000 or higher, the user can press the
Feature key and then the flashing red CO line key (incoming CO call)
to display Caller ID.

A maximum of 16 stations can display Caller ID.

Five users can access the Scroll function at the same time. IN USE
is displayed on the Multiline terminal of another user that tries to
access it.

A maximum of 13 characters can be displayed on the LCD for Caller
ID Name/Number.

Caller ID scrolling and automatic dial out features require installation
of the MIFM-U10 ETU with attached KMM(1.0)U.

When a call transferred to a station goes unanswered and is
transferred again, Caller ID information is not stored in the scrolling
bin at that station.

General:

Caller ID Indication (Analog Trunks)

When the CO line key is flashing red (Incoming CO call), the user can
press F LK to display Caller ID even when Caller ID is not
normally displayed. System Software S3000 or higher is required.

When the telephone company sends the caller name and number,
the name or the number is displayed on the LCD while the Multiline
Terminal is ringing. When the telephone company sends the caller
number only, it is displayed on the top line of the LCD while the
Multiline Terminal is ringing.

A maximum of 15 Multiline Terminals can be assigned to display
Caller ID for normal incoming CO calls system-wide. A sixteenth
Multiline Terminal can be assigned to display Caller ID for normal
incoming CO calls per CO line. These 16 Multiline Terminals
constitute a Caller ID group. An answered call can be transferred to
any station in the system, and Caller ID is displayed at that station.

Press the green line key where the CO call resides during a CO call,
to verify the Caller ID. When the telephone company provides both
Name and Number (depending on the system assignment) they are
displayed for 5 seconds, followed by the remaining information.
System Software S4000 or higher is required to display both
Name and Number.

When the station is assigned to receive DIT/ANA calls, Caller ID is
displayed only on the Multiline Terminal where DIT/ANA is assigned
to ring. The Caller ID Indication follows the station Call Forward
setting or Station Hunting feature.

«
...
137
138
139
140
141
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: Calira Pages: 14

Brand: Happy Orange Pages: 2

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Campbell Pages: 70

Brand: Yuasa Pages: 35

Brand: 3M Pages: 10

Brand: ULTIMATE SPEED Pages: 19

Brand: Galeo Pages: 19

Action Replay DSi

Brand: Datel Pages: 2

CurrentWatch EGF Series

Brand: Eaton Pages: 4

CurrentWatch EGF Series

Brand: Eaton Pages: 2

Brand: Eaton Pages: 4

Brand: LAZER Pages: 6

Brand: Mamiya Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands