NEC Electra Elite 48/192 Features And Specifications Manual Download Page 628 | Manualshive

Page: 628 / 652

background image

Electa Elite

Issue 6

Features and Specifications Manual

V - 7

Restrictions:

The following numbers can be registered as allowable mailbox
numbers for up to a maximum of 200 Voice Mailboxes:

•

2-Digit10~99

•

3-Digit100~999

•

4-Digit1000~9999

Voice Mail MSG Waiting has priority over any other state of the
flashing line key or One-Touch Key.

General:

The state of a One-Touch or Feature Access key is indicated by the
red LED as follows:

•

On Steady Registered Box Number Station is busy

•

Flashing 0.25ON/0.25 OFFRegistered station is in Call Forward-

All Call or Do Not Disturb

•

Flashing

0.5

On/0.5

OFF

Registered station was set by

pressing the Function key

•

Fast flash 0.125 ON/0.125 OFFMailbox contains an unplayed

message

•

OFF

Station is idle or Voice Mailbox
is empty

When the Mailbox registered for multiple Line Keys or One-Touch
Keys contains a message, all programmed keys flash to indicate that
the mailbox contains an unplayed message.

This feature also supports Analog Voice Mail Systems.

When the user of an invalid system station with a mailbox number
assigned to a Feature Access or One-Touch key presses the One-
Touch or Feature Access key while the LED is off, ERROR is
displayed, and an error tone is generated.

When the user of an invalid system station with a mailbox number
assigned to a Feature Access or One-Touch key presses the One-
Touch or Feature Access key while the LED indicates MSG waiting,
the caller is logged into that Mailbox.

When the user of a valid system station with a mailbox number
assigned to a Feature Access or One-Touch key presses the One-
Touch or Feature Access key while the LED indicates MSG waiting,
an internal call is placed to that station.

«
...
626
627
628
629
630
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: Bartington Pages: 11

Brand: Farenheit Pages: 8

Brand: Wagan Pages: 12

Brand: Jabra Pages: 7

Brand: Jabra Pages: 2

Brand: Jabra Pages: 12

SP5050 - Bluetooth hands-free Speakerphone

Brand: Jabra Pages: 221

Brand: Jabra Pages: 22

Brand: Jabra Pages: 42

Brand: Land Pride Pages: 4

Brand: Land Pride Pages: 3

Brand: Natibaby Pages: 24

Brand: Narvitech Pages: 12

Brand: Oki Pages: 2

Brand: Oki Pages: 20

Brand: Oki Pages: 2

FREELANCE XD 5100

Brand: BT Pages: 2

Sleeptrainer Palm the penguin

Brand: NENKO Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands