manualshive.com logo in svg

NEC Electra Elite 48/192, Features And Specifications Manual

The NEC Electra Elite 48/192 is a powerful and reliable communication system. Unlocking its full potential is made easy with the Features And Specifications Manual, a comprehensive guide to unleash the system's capabilities. Download this manual for free at manualshive.com to explore all the advanced features at your fingertips.

Share
Download
background image

Electra Elite                                                                                                                                

                                                   Issue 6

Features and Specifications Manual

D - 23

When a Multiline Terminal user completes Live Record without
specifying a mailbox where the conversation should be stored and
Automatic Recall is not assigned in Digital Voice Mail programming,
the conversation is stored in the mailbox assigned to the Multiline
Terminal.  When a Multiline Terminal user completes Live Record
without specifying a mailbox where the conversation should be
stored and Automatic Recall is assigned in Digital Voice Mail
programming, the conversation is stored in the mailbox assigned to
the Multiline Terminal and the system recalls the Multiline Terminal
and plays the recorded conversation.

(Auto Callback rings - 4 times, Waiting Time - 3 minute, Redial - 5
times.)

Live Record can be used only from Multiline Terminals.

Individual trunks must be assigned for the Live Record feature to
operate.

An alert tone is provided for Live Record. The alert tone is heard by
both the outside party and the Multiline Terminal user when the
recording starts or at specified intervals during recording. The
interval between alert tones is assigned in the Digital Voice Mail
System Programming. The tone lasts for 0.5 seconds. The system
can also be programmed so that an alert tone is not provided.

Up to seven feature keys can be programmed for use with Live
Record.  These feature keys can be assigned to Feature Access
keys, One-Touch keys, or DSS keys (on a DSS/BLF console).  When
the feature keys are assigned to One-Touch keys, no LED
indications are provided. 

The following feature keys can be programmed:

Record Key

Use this key to manually start Live Record. The associated LED
flashes red while recording.  The associated LED goes off when
recording ends or a pause occurs and flashes green when a live
record message is addressed.

Pause Key

Use this key to pause and restart live record.  The associated
LED flashes green when recording has paused.

Erase Key

Use this key to erase the Live Record conversations.  After the
Erase key is pressed, the Voice Mail port remains off-hook until
the call is terminated.

End Key

Use this key to end the Live Record. The conversation can
continue without being recorded.

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Jamara My first Walker Instructions preview
My first Walker
Brand: Jamara Pages: 4
Jalousie-Welt Jupiter Operations And Maintenance, Instructions Of Shipment, Unpacking And Installation preview
Jupiter
Brand: Jalousie-Welt Pages: 20
kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Brand: kaarta Pages: 29
Omron E3Z-LL Manual preview
E3Z-LL
Brand: Omron Pages: 16
MICRO-EPSILON scanCONTROL 25 100 Series Operating Instructions Manual preview
scanCONTROL 25 100 Series
Brand: MICRO-EPSILON Pages: 60
DEFA 412737 Fitting Instructions Manual preview
412737
Brand: DEFA Pages: 7
Prorack K869 Fitting Instructions Manual preview
K869
Brand: Prorack Pages: 15
Baumer UNAM 12N8910/S14OD Manual preview
UNAM 12N8910/S14OD
Brand: Baumer Pages: 3
Sport-Tec Fun 19 Manual preview
Fun 19
Brand: Sport-Tec Pages: 22
Acuity Brands CM ADC Series Manual preview
CM ADC Series
Brand: Acuity Brands Pages: 3
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
Omega Engineering OM-EL-USB-1 Installation & Operating Manual preview
OM-EL-USB-1
Brand: Omega Engineering Pages: 13
Gardena 1188 Operating Instructions Manual preview
1188
Brand: Gardena Pages: 13
Aiwa TN-C526AHRJB Service Manual preview
TN-C526AHRJB
Brand: Aiwa Pages: 18
Compass 02106 Manual preview
02106
Brand: Compass Pages: 16
StarTech.com ATXSILENT Instruction Manual preview
ATXSILENT
Brand: StarTech.com Pages: 10
FEIYUTECH Feiyu Pocket 2S Instructions Manual preview
Feiyu Pocket 2S
Brand: FEIYUTECH Pages: 19
Naish Fusion 5-Line Manual preview
Fusion 5-Line
Brand: Naish Pages: 23

Brands by name

Popular brands

Load more brands