manualshive.com logo in svg

NEC Electra Elite 48/192, Features And Specifications Manual

The NEC Electra Elite 48/192 is a powerful and reliable communication system. Unlocking its full potential is made easy with the Features And Specifications Manual, a comprehensive guide to unleash the system's capabilities. Download this manual for free at manualshive.com to explore all the advanced features at your fingertips.

Share
Download
background image

Electra Elite                                                                                                                                

                    Issue 6

Features and Specifications Manual

C - 31

1.

Lift the handset or press

P

.

2.

Dial Access Code 

DH

 (set as default).

3.

Dial the station number where forwarding is to be canceled.

4.

Wait for the confirmation tone, and restore the handset or press

P

.

1.

Press

T

.

2.

Dial Access Code 

FH

.

3.

Press

T

.

SERVICE 
CONDITIONS

Data Assignment:

Use Memory Block 1-8-07 [Class of Service (Attendant) Feature
Selection 1] Page 2 LK2 to Allow (default: LED On) or Deny (LED
Off) Call Forward - All Call set/reset.

Use Memory Block 1-8-07 [Class of Service (Attendant) Feature
Selection 1] Page 2 LK3 to Allow (LED On) or Deny (default: LED
Off) System-wide reset of Call Forward - All Call.

Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2] Page 1 LK1 to allow (default: LED On) Call Forward - All
Call/DND.

This feature can be assigned on Feature Access or One-Touch keys
using Memory Blocks 2-05 (Line Key Selection) and 2-06 (Line Key
Selection for Tenant Mode) or 4-12 (Line Key Selection for
Telephone Mode).

Restrictions:

At default, system-wide cancel of Call Forward - All Call from
Attendant Positions is denied.

Ring Transfer, Camp-On, and Tone Override cannot be set to a
station that has Call Forward - All Call set.

DND and Call Forward - All Call cannot be set at a station at the
same time.

To cancel at a destination station (Attendant Positions only):

To cancel Call Forward - All Call, Busy/No Answer, and Do Not 
Disturb system-wide (Attendant Positions only):

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Acer WP100 Quick Manual preview
WP100
Brand: Acer Pages: 2
Acer PD100 Quick Start Manual preview
PD100
Brand: Acer Pages: 4
Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
Kappa K132 Manual preview
K132
Brand: Kappa Pages: 4
Panasonic KX-TCD210E Quick Manual preview
KX-TCD210E
Brand: Panasonic Pages: 6
Panasonic KX-TC187B Operating Instructions Manual preview
KX-TC187B
Brand: Panasonic Pages: 32
Panasonic KX-TC180-B User Manual preview
KX-TC180-B
Brand: Panasonic Pages: 3
Panasonic KX-TC1723B Description preview
KX-TC1723B
Brand: Panasonic Pages: 2
Panasonic KX-TC1461B - Cordless Telephone User Manual preview
KX-TC1461B - Cordless Telephone
Brand: Panasonic Pages: 6
Panasonic KX-TA624 Product Description preview
KX-TA624
Brand: Panasonic Pages: 23
Panasonic KX-T7885 - Battery For Operating Instructions Manual preview
KX-T7885 - Battery For
Brand: Panasonic Pages: 48
Panasonic KX-PRX120C Quick Manual preview
KX-PRX120C
Brand: Panasonic Pages: 52
Panasonic KX-PRX120 Quick Manual preview
KX-PRX120
Brand: Panasonic Pages: 48
Panasonic KX-PRW120 Setup Manual preview
KX-PRW120
Brand: Panasonic Pages: 8
Panasonic KX-TA824 Manual preview
KX-TA824
Brand: Panasonic Pages: 3
Panasonic KX-TA824 User Manual preview
KX-TA824
Brand: Panasonic Pages: 12
Panasonic KX-TA308 Instrucciones De Funcionamiento preview
KX-TA308
Brand: Panasonic Pages: 132
Panasonic KX-TA624 Installation Manual Addendum preview
KX-TA624
Brand: Panasonic Pages: 12

Brands by name

Popular brands

Load more brands