NEC Electra Elite 48/192 Features And Specifications Manual Download Page 289 | Manualshive

Page: 289 / 652

background image

D - 80

D

term

® Cordless II Terminal

Issue 6

Electra Elite

1.

Verify that the base unit is in Desk mode.

2.

Remove battery.

3.

Press and hold

J

and

L

on the handset.

4.

Install the battery while holding these keys.

5.

After the handset beeps one time, release the keys.

6.

The handset is in Setup mode.

7.

Press HOLD to display the current mode (Digital/Redial).

8.

Press F2 and then HOLD.

9.

The handset displays Digital (F8), and changes the REDIAL key
program to Desk/Cordless Softkey Switching mode.

10.

Press TALK to restore standby mode.

11.

Press REDIAL to test this feature.

12.

The base unit automatically changes from Desk to Cordless.

Note: This is a one time operation, but one of the F1~F4 keys can be programmed for

the redial function.

13.

To restore the normal redial function, enter setup mode, and
press F3 and HOLD to display Digital (Redial).

14.

Press TALK to restore standby mode.

SERVICE
CONDITIONS

General:

When a message is received the

u

icon is displayed.

When the RING OFF/ON switch on the right side is down the

OFF

icon is displayed

.

When the battery is low, the

icon is displayed.

When there is no transmission between the base unit and the
handset for about five minutes, there are no LCD or LED indications
on the cordless terminal handset. Ringing off-hook or pressing keys
resumes LCD and LED indications.

The ring pattern for the cordless terminal can be selected by System
Programming and Multiline Terminals.

LOW

«
...
287
288
289
290
291
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: Manfrotto Pages: 4

Brand: TaylorMade Pages: 5

Brand: VDO Pages: 91

Brand: CALEFFI Pages: 20

Brand: Olympia Pages: 40

Brand: Oki Pages: 2

Brand: OKIDATA Pages: 16

Brand: X Rocker Pages: 12

Brand: Yealink Pages: 15

Brand: Yealink Pages: 12

Brand: Yealink Pages: 3

Brand: YOKOGAWA Pages: 15

Yealink SIP-T22P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 3

Brand: Öhlins Pages: 10

Brand: +GF+ Pages: 36

Brand: Fantec Pages: 5

Brand: Yoshimura Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands