manualshive.com logo in svg

NEC Electra Elite 48/192, Features And Specifications Manual

The NEC Electra Elite 48/192 is a powerful and reliable communication system. Unlocking its full potential is made easy with the Features And Specifications Manual, a comprehensive guide to unleash the system's capabilities. Download this manual for free at manualshive.com to explore all the advanced features at your fingertips.

Share
Download
background image

Features and Specifications Manual

2 - 1

Features

Chapter 2

S

ECTION

 

1

 

GENERAL 
INFORMATION

All features available with the Electra Elite 48/192 system are listed
alphabetically by name and described in this document. The following
information is provided, when applicable, for each feature:

Feature Description – briefly describes the feature and, when applicable,
tells how the feature is used by the end-user.

System Availability – describes Multiline Terminals that can be used with this
feature. and lists any additional equipment, such as adapters or ETUs, that
must be installed for this feature to operate.

Operating Procedures – contains detailed procedures for using each feature.

Quick Access Code Reference  –  provides a table for those features with
associated Access Codes that are used with the operation of the feature.  This
table has Default, Access Code Name, and Alphabetic Designation columns.

Default – indicates the default values for the Access Codes that are set
when a new system is installed). Access Codes, except for System and
Fixed codes, can be changed in System Programming. 

Access Code Name – indicates the name associated with the Access
Code.  The code type is shown in parentheses at the end of each code
name.  Access Code types include the following: 

•

System Codes are usually 1-digit codes that apply to the operation

of the system. These codes can be changed using Memory Block
1-1-46 [Access Code (1-Digit) Assignment]. 

•

Intercom Codes are 2-digit codes that apply to the associated

feature and indicate Access Codes that can be changed using
Memory Blocks 1-1-46 [Access Code (1-Digit) Assignment] and
1-1-47 [Access Code (2-Digit) Assignment].

•

Feature Codes are typically 3-digit codes and indicate Access

Codes that apply to the associated feature. These codes can be
changed using Memory Blocks 1-1-46 [Access Code (1-Digit)
Assignment] and 1-1-48 [Access Code (3-Digit) Assignment]. 

•

Fixed Codes are set in the system and cannot be changed.

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

GE BAKER HUGHES DPS 5000 Series User Manual preview
BAKER HUGHES DPS 5000 Series
Brand: GE Pages: 36
Oemtools 24991 Operating Instructions And Parts Manual preview
24991
Brand: Oemtools Pages: 8
U.S. General 97845 Set Up And Operating Instructions preview
97845
Brand: U.S. General Pages: 5
DAPU C800 Instructions preview
C800
Brand: DAPU Pages: 4
Xplova G5 Quick Manual preview
G5
Brand: Xplova Pages: 13
3M projectorsleeve User Manual preview
projectorsleeve
Brand: 3M Pages: 14
3LeggedThing PUNKS Instructions Manual preview
PUNKS
Brand: 3LeggedThing Pages: 9
FeiYu Tech WG2 Firmware Upgrade Manual preview
WG2
Brand: FeiYu Tech Pages: 5
FEIYUTECH VLOG Pocket Instructions Manual preview
VLOG Pocket
Brand: FEIYUTECH Pages: 19
FeiYu Tech SCORP-C Instructions Manual preview
SCORP-C
Brand: FeiYu Tech Pages: 25
FEIYUTECH SPG Manual preview
SPG
Brand: FEIYUTECH Pages: 16
Lanier 5613 Material Safety Data Sheet preview
5613
Brand: Lanier Pages: 3
quadient IS-240 Replacement Manual preview
IS-240
Brand: quadient Pages: 2
QSC AcousticDesign AD-S52 Install Manual preview
AcousticDesign AD-S52
Brand: QSC Pages: 4
Uniden 2.4 Owner'S Manual preview
2.4
Brand: Uniden Pages: 68
Rally Pack 04910 Installation Instructions preview
04910
Brand: Rally Pack Pages: 2
rako WP-CONC Instruction Manual preview
WP-CONC
Brand: rako Pages: 3
rako WAVMI User Manual preview
WAVMI
Brand: rako Pages: 7

Brands by name

Popular brands

Load more brands