NEC Electra Elite 48/192 Features And Specifications Manual Download Page 46 | Manualshive

Page: 46 / 652

background image

Features and Specifications Manual

A - 25

Answer Key

A-9

FEATURE
DESCRIPTION

Multiline Terminals have an Answer key with an LED that flashes when the
Multiline Terminal user receives an incoming CO/PBX, Tie/DID transfer, or
CO/PBX transfer call ringing in the same tenant group. When multiple calls
are received, the Answer key is used to pick up calls. The Answer key
continues flashing until the last unanswered call is answered. Press the
Answer key during a call to hold the current call and allow the next call to be
answered.

SYSTEM
AVAILABILITY

Terminal Type:

All Multiline Terminals

Required Components:

None

OPERATING
PROCEDURES

1.

Receive CO/PBX incoming ring.

O

LED flashes.

2.

Press

O

. The

O

LED goes out.

3.

Talk with the CO/PBX incoming calling party.

4.

When additional CO incoming calls are received, the

O

LED

flashes again. Press

O

to place the current call on Non-

Exclusive Hold and connect the Multiline Terminal user to the next
call.

a.

An original call on a Call Appearance Key is placed on
Non-Exclusive Hold on the Call Appearance Key.

b.

An original call on a line key is placed on Non-Exclusive Hold
on the line key.

To answer calls using the Answer key:

«
...
44
45
46
47
48
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: Manfrotto Pages: 2

Univerge SV8100

Brand: NEC Pages: 1174

Brand: Samsung Pages: 2

Brand: Barracuda Pages: 3

Ergopower Record 12s

Brand: CAMPAGNOLO Pages: 124

Brand: CAMPAGNOLO Pages: 100

GFS 10 - Fuel Sensor

Brand: Garmin Pages: 2

Brand: Harmar Mobility Pages: 10

Brand: Navibe Pages: 8

SmartSensor Matrix

Brand: Wavetronix Pages: 2

Brand: Watt Stopper Pages: 8

WORKCENTRE C2424

Brand: Xerox Pages: 2

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 8

Brand: GE Pages: 60

Brand: Oki Pages: 20

Brand: Uniden Pages: 68

KX-TG2267B - GigaRange - 2.4 GHz Digital Cordless...

Brand: Panasonic Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands