NEC Electra Elite 48/192 Features And Specifications Manual Download Page 74 | Manualshive

Page: 74 / 652

background image

Electra Elite

Issue 6

Features and Specifications Manual

A - 53

1.

Receive an incoming CO/PBX call.

2.

The Automatic Answer with Delay Message answers the call and
sends a greeting.

3.

The outside party hears ringback tone or MOH (System
Programmed).

4.

After the time expires, a second message is played.

5.

The outside party hears ringback tone or MOH until the call is
answered.

SERVICE
CONDITIONS

Data Assignment:

A maximum of two VRS(4)-U10 ETUs, four channels per ETU, can
be used for Automated Attendant.

Each channel has 240 recording seconds that can be subdivided into
2, 4, 8, or 16 equal recording times.

A maximum of eight Automated Attendants can be assigned.

Use Memory Block 1-4-11 (Automated Attendant Message Day/Night
Mode Selection) to assign the Day/Night/Weekend mode greeting
messages to each Automated Attendant position.

Use Memory Block 1-4-13 (Automated Attendant Answer Delay Time
Assignment) to set the answering time (default: 4 seconds) between
when the incoming CO/PBX call rings and when it is answered. This
time affects the Day/Night/Weekend mode settings per Automated
Attendant.

Use Memory Block 1-4-16 (Automated Attendant Message Repeat
Selection) to assign the number of times a greeting message is
repeated (default: 1).

Use Memory Block 1-8-07 [Class of Service (Attendant) Feature
Selection 1] Page 1 LK8 to Allow (default: LED On) or Deny (LED
Off) Attendant Positions to set/reset the Automated Attendant per
trunk.

Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2] Page 2 LK6 to Allow (default: LED On) or Deny (LED
Off) the station to record, verify, or erase an Automated Attendant
message.

To answer by Two Levels:

«
...
72
73
74
75
76
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: GE Pages: 2

Brand: I-G3N Pages: 28

Brand: Ranger design Pages: 6

Brand: K&M Pages: 9

BTL7-S5 B-M Series

Brand: Balluff Pages: 14

BML-S1G0 7 M5E 0 Series

Brand: Balluff Pages: 194

Brand: Parkside Pages: 89

Brand: Parkside Pages: 28

Brand: Xerox Pages: 2

Brand: Barker Pages: 2

efector 190 DTE820

Brand: IFM Electronic Pages: 16

Brand: LU-VE Pages: 8

Brand: Obelink Pages: 2

ANDROID INTERFACE

Brand: GMC Pages: 18

Brand: Prorack Pages: 15

Brand: REVCAMUK Pages: 4

Brand: SMC Networks Pages: 80

Brand: Ednet Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands