NEC Electra Elite 48/192 Features And Specifications Manual Download Page 129 | Manualshive

Page: 129 / 652

background image

C - 10

Call Arrival (CAR) Keys

Issue 6

Electra Elite

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 1-2-04 (Call Arrival Key Block Assignment) to
assign Call Arrival extensions in groups of four.

Use Memory Block 2-06 (Line Key Selection for Tenant Mode) to
assign Call Arrival keys to a CAP block in Tenant Mode.

Use Memory Block 4-12 (Line Key Selection for Telephone Mode) to
assign Call Arrival keys to a CAP block in Telephone Mode.

Read the CAP Key features and specifications because CAR and
CAP can be closely related.

Restrictions:

The Electra Elite 192 system can provide 112 Call Arrival keys. This
number is shared with 120 station ports. When 112 CAR keys are
assigned, the remaining eight numbers can be assigned for hardware
extension numbers.

Using System Software S3000 or lower, the Electra Elite 48
system can contain 24 Call Arrival keys. This number is shared with
32 station ports. When 24 CAR keys are assigned, the remaining
eight numbers can be assigned for hardware extension numbers.

Using System Software S4000 or higher, the Elite 48 system can
have a maximum of 40 CAR key extensions and 8 stations ports or
32 station ports and 16 CAR ports.

General:

Incoming outside line calls can ring on a CAR. When the call is
answered, it resides on a CAP (or CO Line key). The CAR becomes
idle for another incoming call or continues to flash when another call
is waiting to be answered. When a Call Appearance key (or CO Line
key) is unavailable, an outside line call to a Call Arrival key cannot be
answered.

Incoming internal calls to a Call Arrival key can be answered with a
Call Appearance key unassigned. The ICM lamp (when provided)
indicates a call, and when the call is put on hold, flashes at the
Conference key.

Go off-hook, press the Speaker key when Ringing Line Preference is
assigned, press the flashing Call Arrival key, or press the Answer key
to answer Calls ringing at a Call Arrival key.

Call Arrival Keys can be set for Call Forward - All Call and Call
Forward - Busy/No Answer.

Using System Software S4000 or higher, Call Arrival keys can be
set for Call Forward - Off Premise.

«
...
127
128
129
130
131
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: Sangoma Pages: 3

Brand: XPLORA Pages: 2

Brand: Octopus Pages: 122

Brand: LAZER Pages: 13

Brand: Latento Pages: 60

Brand: Easy Quick Pages: 11

Brand: Radio Shack Pages: 2

Brand: E-MetroTel Pages: 4

Brand: Panasonic Pages: 10

AVCCAM AG-HMR10

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 10

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Abus Pages: 2

Brand: Garmin Pages: 14

Brand: Yealink Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands