NEC Electra Elite 48/192 Features And Specifications Manual Download Page 187

Page: 187 / 652

C - 68

Class of Service

Issue 6

Electra Elite

At default, all stations are set for Class 00 using Memory Block 4-17
(Station to Class of Service Feature Assignment).

General:

Each Class of Service provides 16 different Classes.

The following Attendant features can be allowed/denied in each
class for Class of Service assignment (Attendant) Feature Selection
1:

Features

Default

Values

(All

Stations)

Night Mode Switching (System-Wide)

Allow

Night Mode Switching (Tenant)

Allow

System Speed Dial Programming

Allow

Automatic Trunk-to-Trunk Transfer (Set/Reset) and
Programming of Outgoing Numbers

Allow

Automated Attendant Mode/DISA Mode (Set/Reset)

Allow

Timed Alarm (Set/Reset) for Single Line
Telephones (From Attendant

Allow

Call Forward-All Call (Set/Reset) from Destination
Station
Call forward CAR extensions
Call forward BNA

Allow

System-Wide Reset of Timed Alarm, Call Forward-
All Call, Do Not Disturb, Customized Message, and
Callback Request

Deny

Cancel Station Lockout and Default Password for
Another station

Allow

DISA Password Cancel

Allow

DISA Password Confirmation

Allow

Automated Attendant Weekend Mode (Set/Reset)
per Tenant

Allow

Forced Account Code Programming

Allow

Terminal Exchange Mode Set

Allow

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Electra Elite 48/192

Reviews:

Related manuals for Electra Elite 48/192

Brands by name

Popular brands

NEC Electra Elite 48/192, Features And Specifications Manual

Search results

Summary of Contents for Electra Elite 48/192

Reviews:

Related manuals for Electra Elite 48/192

Brands by name

Popular brands