NEC Electra Elite 48/192 Features And Specifications Manual Download Page 546 | Manualshive

Page: 546 / 652

background image

Electra Elite

Issue 6

Features and Specifications Manual

S - 41

Multifunction (Dial Access) only:

1.

Lift the handset, and wait for internal dial tone.

2.

Dial the Speed Dial Access Code (default:

GG

).

3.

Dial the System Speed Dial buffer number (use

KK

~

GI

or

KKK

~

III

.

4.

Talk with called party.

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 1-8-07 [Class of Service (Attendant) Feature
Selection 1] Page 1 LK3 to allow (default: LED On) or Deny (LED
Off) System Speed Dial programming for each Class of Service.

Use Memory Block 1-1-35 (Speed Dial Buffer Allocation) to select
100-memory (default) or 1000-memory allocation. The 100-memory
mode includes 80 System Speed Dial Buffers and 20 Station Speed
Dial Buffers. The 1000-memory mode has 1000 System Speed Dial
Buffers.

Use Memory Block 1-1-18 (System Speed Dial Restriction by
Tenant) to specify unrestricted (LED On) or restricted (LED Off)
System Speed dial for each tenant (Default: All LEDs On). When 80
System Speed Dial mode is used, blocks have groups of 10 buffers.
When 1000 System Speed Dial mode is used, the blocks are divided
by groups of 100 buffers.

Use Memory Block 1-1-62 (System Speed Dial Override by Class
Selection) to specify whether (default: YS) or not (NO) Class
Selection can override Speed dial per Class.

Restrictions:

When 1000 System Speed Dial buffers (000~999) are available,
Station Speed Dial buffers cannot be assigned.

General:

When using 1000 System Speed Dial mode, buffers 900~999 cannot
be restricted from any tenant.

System Speed Dial blocks can be shared by one or more tenants.

To use a System Speed Dial buffer using a Single Line
Telephone:

«
...
544
545
546
547
548
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: CAB Pages: 10

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

Brand: Calira Pages: 14

Brand: Baja Designs Pages: 6

XMODS Custom RC

Brand: Radio Shack Pages: 4

Brand: Vanderbilt Pages: 10

Brand: ZARD Pages: 2

Brand: Nanoleaf Pages: 14

Brand: Xerox Pages: 16

COPENHAGEN WHEEL

Brand: Superpedestrian Pages: 52

Brand: OBO Bettermann Pages: 2

Brand: GATmatic Pages: 13

Brand: Katranji Pages: 2

Brand: Metra Electronics Pages: 2

00.15189.002 050

Brand: Lambrecht Pages: 10

Brand: DEFA Pages: 9

Slim Line LED Light Grille Kit

Brand: rough country Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands