NEC Electra Elite 48/192 Features And Specifications Manual Download Page 212 | Manualshive

Page: 212 / 652

background image

Features and Specifications Manual

D - 3

Delay Announcement

D-2

FEATURE
DESCRIPTION

Delay Announcement activates when an incoming call to an Automatic Call
Distribution (ACD) or Uniform Call Distribution (UCD) group encounters all
ACD/UCD stations busy or receives no answer within a programmed time.
The call is queued and receives a recorded announcement after a
programmed time. First and second Delay Announcements are available.
The incoming call can be Direct Inward Termination (DIT/ANA), CO Ring
Transfer, Automated Attendant Transfer, or DID/Tie line.

ACD is not supported by the Electra Elite 48 system.

SYSTEM AVAILABILITY

Terminal Type:

Not applicable

Required Components:

VRS(4)-U10 ETU is required for recorded announcement

MIFA-U10 ETU is required for UCD

In the Electra Elite 192 system, MIFA-U10 ETU and KMA(1.0)U are required
for ACD.

OPERATING
PROCEDURES

Refer to

A-16 Automated Attendant

, for these instructions.

1.

An incoming call to an ACD/UCD group is received.

2.

The First Delay Announcement answers the caller.

3.

After the message, the call is connected to Music on Hold.

4.

The Second Delay Announcement answers the caller after a
programmed time.

To record a Delay Announcement:

To process an incoming call:

«
...
210
211
212
213
214
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: Pacbrake Pages: 9

Brand: Ecco Pages: 4

Brand: Danfoss Pages: 4

Formula F732 WIZARD

Brand: Datalogic Pages: 2

Brand: Echo Pages: 4

Brand: Eaton Pages: 2

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: Pitney Bowes Pages: 22

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Tunturi Pages: 37

Brand: Pyle Pages: 4

Brand: Gared Sports Pages: 12

Brand: TeraBee Pages: 27

Brand: Yakima Pages: 11

Brand: TAKARA Pages: 2

Brand: Ozeanos Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands