manualshive.com logo in svg

NEC Electra Elite 48/192, Features And Specifications Manual

The NEC Electra Elite 48/192 is a powerful and reliable communication system. Unlocking its full potential is made easy with the Features And Specifications Manual, a comprehensive guide to unleash the system's capabilities. Download this manual for free at manualshive.com to explore all the advanced features at your fingertips.

Share
Download
background image

Electra Elite                                                                                                                                

                                                   Issue 6

Features and Specifications Manual

A - 7

Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2], Page 6 LK3 to Allow (LED On) or Deny (default: LED
Off) Account Code Forced/Unverified.  System software S5000 or
higher is required.

Use Memory Blocks 1-1-46~48 [Access Code (1-, 2-, or 3-Digit)
Assignment] to assign the Forced Account Code Access (Function
No. 147).

Use Memory Block 1-8-27 (Forced Account Code Length
Assignment) to assign the number of digits for Account Codes
system-wide.  One to 13 digits can be assigned; default is 10 digits.

Use Memory Block 7-1 (Card Interface Slot Assignment) to specify
the necessary MIFM-10 ETU.

Restrictions:

Existing restrictions and Least Cost Routing (LCR) assignments are
applied after Forced Account Codes are entered.

When a 911 call is placed, Account Code Forced/Verified is
overridden by the following:

•

Emergency 911 Cut-Through is enabled.

•

A CAMA trunk is installed and enabled.

Enhanced 911 calls override the forced account code and are
controlled by the Emergency 911 Dialing Route Assignment. 

Verified and Unverified Forced Account Codes cannot be used in the
same Class of Service.

General:

System Software S5500 or higher is required for Scrolling
Directories to be used with this feature.

Only outgoing calls from an intercom require a Forced Account
Access Code.  Direct access to trunks bypasses this feature.

Reorder tone is provided when an outgoing call is dialed without
entering the Forced Account Access Code and a Forced Account
Code.

Call Alert Notification is not provided during Account Code Entry
verification and programming. 

PBR Time values apply when a Single Line Telephone is used to
enter a Forced Account Code.

Forced Account Codes can be uploaded, downloaded, or modified
using PC based System Programming.

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Canon Super G3 FAX Board-T1 Portable Manual preview
Super G3 FAX Board-T1
Brand: Canon Pages: 16
Canon iP4000 - PIXMA Photo Printer Instruction Manual preview
iP4000 - PIXMA Photo Printer
Brand: Canon Pages: 3
Canon Finisher-U1 Installation Procedure preview
Finisher-U1
Brand: Canon Pages: 21
Canon LV-7275 Starter Manual preview
LV-7275
Brand: Canon Pages: 6
Canon 7215 - LV XGA LCD Projector Assembly & Installation Manual preview
7215 - LV XGA LCD Projector
Brand: Canon Pages: 8
Quincy lab 140 Series Operating Manual preview
140 Series
Brand: Quincy lab Pages: 4
Yolin YL80C Manual preview
YL80C
Brand: Yolin Pages: 25
EAL Formula 523585 Assembly Instructions preview
Formula 523585
Brand: EAL Pages: 4
Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
UNIT 1 FARO User Manual preview
FARO
Brand: UNIT 1 Pages: 23
Kabuto FIGO Instruction Manual preview
FIGO
Brand: Kabuto Pages: 16
Xerox Phaser 6360 Supplementary Manual preview
Phaser 6360
Brand: Xerox Pages: 13
Xerox DocuColor 242 Release Note preview
DocuColor 242
Brand: Xerox Pages: 41
iArmor IA-N179 Manual preview
IA-N179
Brand: iArmor Pages: 6
Calix M5T 187A Assembly Instructions preview
M5T 187A
Brand: Calix Pages: 5
Mobile Create MCM3 Instruction Manual preview
MCM3
Brand: Mobile Create Pages: 15
Corsair CRYSTAL 680X RGB Manual preview
CRYSTAL 680X RGB
Brand: Corsair Pages: 28
Whispbar K561W Fitting Instructions Manual preview
K561W
Brand: Whispbar Pages: 15

Brands by name

Popular brands

Load more brands