NEC Electra Elite 48/192 Features And Specifications Manual Download Page 601 | Manualshive

Page: 601 / 652

background image

U - 2

Uniform Call Distribution (UCD)

Issue 6

Electra Elite

Night Service

When the UCD group is placed in Night Mode, the system can route all
incoming UCD calls to Internal Station Number, Night Announcement,
transfer to the Attendant, or Trunk-to-Trunk Transfer.

Overflow

Overflow allows calls, holding in queue for more than a programmed time,
to be directed to an assigned station or Station Hunting group.

Queuing

All incoming calls destined for UCD groups are placed in queue when no
Agent in the UCD group can handle the call. Queue is used to provide
service in order of arrival (first in, first out).

Pilot Numbers

Pilot Numbers are programmed in the System Data according to the
numbering plan assigned for the system. Pilot Numbers do not correspond
to any line appearances, either physical or virtual, in the Electra Elite 48/
192 systems. No hardware equipment is required to assign a Pilot number.
A UCD Group Pilot number does not function when programmed in a
Station Hunt group.

AGENT AND SUPERVISOR FUNCTION

This section includes the following features:

Assistance

This feature allows an Agent to call a UCD group Supervisor for
assistance. Activating this feature while on a UCD call, automatically
places the current call on hold and places an assistance call to the
Supervisor. This feature uses a Feature Access or One-Touch key.

Break Mode

This feature allows Agents to leave the UCD Mode without logging off.
Break Mode is used for breaks from work (e.g., lunch or coffee breaks).
This feature uses a DND key that is programmed on a Feature Access or
One-Touch key. If DND, Call Forward - All Call/Busy/No Answer was
programmed before Log on, non-UCD calls follow the programmed
function while in Break Mode.

«
...
599
600
601
602
603
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: GDC Pages: 64

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

KX-TG7622, KX-TG7623, KX-TG762

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 6

Brand: Waycon Pages: 4

Brand: Bachmann Pages: 2

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Pages: 2

Brand: Oki Pages: 2

Brand: Oki Pages: 20

Brand: Oki Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands