NEC Electra Elite 48/192 Features And Specifications Manual Download Page 57 | Manualshive

Page: 57 / 652

background image

A - 36

Attendant Camp-On

Issue 6

Electra Elite

1.

The user engaged in a call receives a camp-on tone. The

O

flashes red, the Large LED flashes green, and CO/PBX line

flashes green, when assigned.

2.

Press

O

and talk with the CO/PBX incoming caller. The

previous call is put on hold.

1.

The user engaged in a call receives a camp-on tone.

2.

Hang up or put the call on System Call Park.

3.

Go off-hook, and talk with the CO/PBX incoming caller.

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 1-1-11 (System Transfer/Camp-On Selection) to
select whether (default: YS) or not (NO) the station user can press
the transfer key to perform a Station Camp-On.

Use Memory Block 1-1-64 (Attendant Add-On Console Transfer/
Camp-On Recall Time Selection) to set the Attendant Camp-On
Recall Time for 0.5 (default), 1.5, 2, 3, 5, 8, or 10 minutes.

Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2] Page 3 LK3 to Allow (default: LED On) or Deny (LED
Off) receiving a Camp-On tone.

Restrictions:

Camp-On is not allowed to stations that have received Tone
Override.

General:

The camp-on tone is heard over the handset or from the speaker
when the Multiline Terminal is in handsfree mode.

Any number of outside calls can be camped on to a station. When
the station goes idle, the Camp-On calls are answered in order from
the lowest numbered lines to the highest numbered lines.

To answer a Camp-On Call from a Multiline Terminal:

To answer a Camp-On Call from a Single Line Telephone:

«
...
55
56
57
58
59
...
»

Summary of Contents for Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Electra Elite 48/192

Brand: K&M Pages: 9

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 289

Brand: Panasonic Pages: 60

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 36

T-Mobile KX-HDV130

Brand: Panasonic Pages: 35

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 11

Brand: Panasonic Pages: 8

KXDT346 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 5

KXDT321 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 24

DECT Portable Station KX-TCA256

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 18

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 280

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands