background image

Automation Components, Inc.

2305 Pleasant View Road  |  Middleton, WI 53562

Phone:

 1-888-967-5224  |  

Website:

 workaci.com

Page 1

FIGURE 1: 

ENCLOSURE 

DIMENSIONS

BACnet / Modbus IMMERSION SERIES

Installation & Operation Instructions

Phone:

 1-888-967-5224

Website:

 workaci.com

GENERAL INFORMATION

The BACnet MS/TP / Modbus RTU Immersion Series 
sensor is designed for use with electronic controllers 
in commercial heating and cooling building manage-
ment systems. The ACI BACnet MS/TP / Modbus RTU 
Immersion Series sensor can be ordered to monitor 
temperature in commercial HVAC pipes. It uses 
BACnet MS/TP or Modbus for RTU for physical 
connection to a BAS or controller, has dip switches to 
set addresses and baud rate, parity and stop bits 
(Modbus RTU only) and has on board end-of-line 
termination. There is no analog output.

WIRING INSTRUCTIONS

The BACnet/Modbus RTU Immersion Series 
temperature sensor has a depluggable terminal 
block located on the front of the PCB. For ease of 
wiring, we recommend removing the block, wiring, 
and reattaching before mounting. 16 to 22 AWG 
two conductor shielded cable is recommended for 
powering the sensors. 

ACI recommends using Belden 3105 or compatible 
cable for RS-485 communication wiring. This wire has 
120 ohm input impendence. The terminal blocks 
allow for (1) or (2) wires to be connected in each 
position for daisy chaining. Daisy chain the RS-485 
wiring and do not use “Star” or “T” wiring. Avoid 
running communication wires next to AC line 
voltage wires. These can be sources of noise that can 
affect signal quality.

PRECAUTIONS
• Remove power before wiring. Never connect 

or disconnect wiring with power applied.

•  It is recommended you use an isolated 

UL-listed class 2 transformer when powering 
the unit with 24 VAC. Failure to wire the devices 
with the correct polarity when sharing 
transformers may result in damage to any 
device powered by the shared transformer. 

3.60"

(91.44 mm)

2.25"

(57.15 mm)

4.79"

(121.55 mm)

2.35"

(59.80 mm)

TABLE 1: 

WIRING CONNECTIONS

CONNECTIONS

Power Supply Positive 12-36 VDC / 24 VAC
Power Supply Common or Ground
EIA-485 Data Negative
EIA-485 Data Positive

TERMINAL 
BLOCKS

+V
GN
D-
D+

FIGURE 2: 

LAYOUT

DIP SWIT

CH

BAU
D

ADDRESS

OFF

ON

PA

R

SW4

BAC

NET

MOD

BUS

RESET

BUTTON

END OF LINE

TERMINATION

LED

EN

DIS

D+

D-

GN

V

64

32

16

8

4

2

1

4

2

1

1

ON

1

2

2
3
4

TERMINAL

BLOCKS

Version: 2.0

I0000929

Summary of Contents for BACnet / Modbus IMMERSION Series









Reviews: