AirCaddy K8350 Instruction Sheet Download Page 1

Page: 1 / 12

Home

Instruction Sheet

(1) B1000-00 FOLDED TRIANGULAR

CORRUGATED BOX

39”L X 31”W X 3”H

Step-1

Please check for

any missing parts.

Model K8350

(Aircraft Kit)

(Optional)

(2) C3755-00 LARGE

CORRUGATED INSERTS

(1) B3210-00 METAL TRANSIT PLATE

(6)B1220-00 FLAT NYLON TIES

(1) B1250-00 SADDLE TRAVEL BAG

Model K9100 COMPACT

(Basic AirCaddy)

(1) T3230-00 METAL WHEEL TRUCK

(1) B1382-00 5MM AND 6MM ALLEN

(6) B1220-00 FLAT NYLON TIES

(1) B1350-00 2 INCH WIDE

TAPE AND DISPENSER

IRCADDY.com

Worldwide Cycling Solutions Through Creative Innovations.

(1)T3197-00 METAL FORK MOUNT

aircaddy web page 20 04/03/12 98%

(1) S7035-00
7MM AXLE WASHER

(2) C3750-00 SMALL

CORRUGATED INSERTS

2012 K9100 COMPACT

Because of the constant evolution of our products the

materials and colors are subject to change without notice.

(1) B1250-00 SADDLE TRAVEL BAG

31” width

39” length

Summary of Contents for K8350













Search results

Summary of Contents for K8350

Reviews:

Related manuals for K8350

Brands by name

Popular brands

AirCaddy K8350, Instruction Sheet

Search results

Summary of Contents for K8350

Reviews:

Related manuals for K8350

Brands by name

Popular brands