MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 213

Page: 213 / 256

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

213

7545652/00 EN

VACUTAP

VR-Ex

1. Ground the on-load tap-changer. To do this, only connect the grounding

terminal on the on-load tap-changer head with the transformer cover.

Figure 247: Grounding terminal on on-load tap-changer head

2. Ground the motor-drive unit. To do this, only connect the motor-drive

unit's ground connection with protection against twisting to the trans-
former's ground connection.

Figure 248: Grounding screw on motor-drive unit

3. Connect housing of temperature sensor with grounding screw on on-load

tap-changer head.

6.1.3 Checking motor-drive unit

NOTICE

Damage to the on-load tap-changer / de-energized tap-changer!

Damage to the on-load tap-changer / de-energized tap-changer due to actu-
ation of the on-load tap-changer / de-energized tap-changer without insulat-
ing fluid.

► Ensure that the selector / de-energized tap changer is fully immersed in

insulating fluid and that the oil compartment of the on-load tap-changer is
completely filled with insulating fluid.

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands