MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 79

Page: 79 / 256

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

7545652/00 EN

VACUTAP

VR-Ex

► Screw the potential connection unit to the take-off ring of the oil compart-

ment.

Figure 76: Fastening potential connection unit

1 Nut

5 Spring washer

2 Washer

6 Screening cap

3 Spacing sleeve

7 Screw

4 Mounting bracket

5.3.2 Connecting the tap winding and on-load tap-changer take-off

lead

NOTICE

Damage to the on-load tap-changer!

Connecting leads that place mechanical strain on the on-load tap-changer
will damage the on-load tap-changer.

► Establish connections carefully.

► Do not twist connection contacts.

► Connect connecting leads without warping or deforming.

► If necessary, use an expansion loop for connecting leads.

► Fit screening caps provided to screw connections.

The tap winding and on-load tap-changer take-off lead must be connected in
accordance with the connection diagram included with the delivery.

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands