MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 157 | Manualshive

Page: 157 / 256

background image

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

157

7545652/00 EN

VACUTAP

®

VR-Ex

3. Fasten oil suction pipe to mounting bracket with cable tie provided. Turn

the cable tie so the closure is facing in toward the mounting bracket.

Figure 174: Cable tie

5.4.7.5 Inserting tap position indicator disk

Due to the coupling pin, the tap position indicator disk can only be installed
when in the correct position.

► Place tap position indicator disk on indicator drive shaft, slide spring clip

on to shaft end.

Figure 175: Tap position indicator disk

5.4.7.6 Securing on-load tap-changer head cover

NOTICE

Damage to the on-load tap-changer!

A missing or damaged o-ring as well as unclean sealing surfaces lead to in-
sulating fluid escaping and therefore to damage to the on-load tap-changer.

► Ensure that the o-ring is positioned untwisted in the on-load tap-changer

head cover.

► Ensure that the o-ring does not become damaged when mounting the

cover.

► Ensure that the sealing surfaces on the on-load tap-changer head cover

and on-load tap-changer head are clean.

«
...
155
156
157
158
159
...
»

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR-Ex

Brand: GBC Pages: 8

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: Armarge Pages: 12

Brand: Schmalz Pages: 36

Brand: zitrek Pages: 37

Power Panel T30

Brand: B&R Pages: 140

Brand: Tow Tuff Pages: 6

POWERNET EX MDU

Brand: SA Pages: 8

NA5-12 101 Series

Brand: Omron Pages: 22

Ability MACHsense-R

Brand: ABB Pages: 74

Brand: ABB Pages: 18

Termix VVX-IV 7 Series

Brand: Danfoss Pages: 32

ECX-1400 Series

Brand: Vecow Pages: 146

Brand: SteelMax Pages: 44

Brand: Axminster Trade Pages: 42

Brand: ARGEAD Pages: 6

Brand: nVent RAYCHEM Pages: 21

Brand: Spedo Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands