MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 143

Page: 143 / 256

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

143

7545652/00 EN

VACUTAP

VR-Ex

NOTICE

Damage to the on-load tap-changer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer.

► Ensure that parts do not fall into the oil compartment.

► Check that all small parts are accounted for.

1. Ensure that the inspection window is sealed off with the cover.

2. Remove the screws and washers from the on-load tap-changer head

cover.

Figure 148: On-load tap-changer head cover

3. Remove on-load tap-changer head cover.

Figure 149: On-load tap-changer head cover

5.4.5.2.3 Opening kerosene drain plug

►

NOTICE!

Never remove the kerosene drain plug completely. Only un-

screw the kerosene drain plug between the oil compartment base and se-
lector gear clockwise until it starts to become hard to open.

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands