MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 203

Page: 203 / 256

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

203

7545652/00 EN

VACUTAP

VR-Ex

2. Calculate inside width B between the housings of the upper gear unit and

the bevel gear. Cut down the protective cover to B-2 mm and deburr the
cut edges.

Figure 235: Shortening and deburring the protective cover

3. For the separate grounding with 110 mm spacing from the bevel gear, drill

an 11 mm diameter hole in the protective cover. Protect the protective
cover against corrosion with a coat of paint.

Figure 236: Producing the grounding hole on the protective cover

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands