MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 91

Page: 91 / 256

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

7545652/00 EN

VACUTAP

VR-Ex

3. Screw the on-load tap-changer head cover onto the on-load tap-changer

head.

Figure 88: On-load tap-changer head cover

5.3.5.2 Vapor-phase drying in the autoclave

If you wish to perform another transformer ratio test after drying, proceed as
described in the section "Performing transformer ratio test following dry-
ing" [

►

Section 5.3.8, Page 110].

5.3.5.2.1 Moving on-load tap-changer to adjustment position

► Move the on-load tap-changer to the adjustment position. The adjustment

position is indicated in the on-load tap-changer connection diagram in-
cluded in delivery.

5.3.5.2.2 Removing on-load tap-changer head cover

WARNING

Danger of explosion!

Explosive gases under the on-load tap-changer head cover can deflagrate
or explode and result in severe injury or death.

► Ensure that there are no ignition sources such as open flames, hot sur-

faces or sparks (e.g. caused by the build-up of static charge) in the imme-
diate surroundings and that none occur.

► De-energize all auxiliary circuits (for example tap-change supervisory de-

vice, pressure relief device, pressure monitoring device) before removing
the on-load tap-changer head cover.

► Do not operate any electrical devices during the work (e.g. risk of sparks

from impact wrench).

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands