MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 95

Page: 95 / 256

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

7545652/00 EN

VACUTAP

VR-Ex

2. Position the on-load tap-changer head cover on the on-load tap-changer

head in such a way that the red triangular markings on the on-load tap-
changer head and the on-load tap-changer head cover are aligned.

Figure 93: On-load tap-changer head cover with o-ring

3. Screw the on-load tap-changer head cover onto the on-load tap-changer

head.

Figure 94: On-load tap-changer head cover

5.3.6 Drying on-load tap-changer in transformer tank

Dry on-load tap-changer in accordance with the following instructions to en-
sure the dielectric values assured by MR on the on-load tap-changer.

If you want to dry the on-load tap-changer in the transformer tank, fully as-
semble the transformer first and then undertake drying.

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands