MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 153 | Manualshive

Page: 153 / 256

background image

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

153

7545652/00 EN

VACUTAP

®

VR-Ex

2. Lower and position the top part of the on-load tap-changer head on

mounting flange so that the triangular markings, pins and mounting holes
on the top part and bottom part of the on-load tap-changer head are
aligned.

Figure 166: Markings and aligning pins

5.4.7.3 Connecting on-load tap-changer to top part of on-load tap-changer

head

NOTICE

Incorrectly lifting the on-load tap-changer will damage it!

If the connection screws of the supporting flange are used to lift the on-load
tap-changer, the screws may be damaged, which makes it impossible to
properly screw the on-load tap-changer and the on-load tap-changer head
together!

► Always lift the on-load tap-changer with the specified lifting traverse, and

never with the connection screws of the supporting flange.

1.

NOTICE!

Damage to the on-load tap changer due to escaping insulating

fluid. Ensure that the seal in the oil compartment is clean, intact, and not
twisted.

«
...
151
152
153
154
155
...
»

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR-Ex

Brand: National Instruments Pages: 10

Brand: Garrick Pages: 8

Brand: M-system Pages: 4

Brand: UNITED Pages: 45

Brand: Cooper Pages: 60

Brand: Danfoss Pages: 25

Brand: Axminster Pages: 32

Brand: TE Connectivity Pages: 65

Brand: Panduit Pages: 3

Brand: VEMAG Pages: 167

Brand: PPI Pages: 32

LaserPro StellarMark CIIA-Li

Brand: GCC Technologies Pages: 69

Brand: Halfen Pages: 12

Brand: Jäger Pages: 36

A-GAGE MINI-ARRAY MACNXDN-1

Brand: Banner Pages: 24

Brand: YZ Systems Pages: 44

Brand: ALFRA Pages: 44

Brand: KSB Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands