MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 130

Page: 130 / 256

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

130

7545652/00 EN

VACUTAP

VR-Ex

5.4.2 Connecting the tap winding and on-load tap-changer take-off

lead

NOTICE

Damage to the on-load tap-changer!

Connecting leads that place mechanical strain on the on-load tap-changer
will damage the on-load tap-changer.

► Establish connections carefully.

► Do not twist connection contacts.

► Connect connecting leads without warping or deforming.

► If necessary, use an expansion loop for connecting leads.

► Fit screening caps provided to screw connections.

The tap winding and on-load tap-changer take-off lead must be connected in
accordance with the connection diagram included with the delivery.

5.4.2.1 Selector connection contacts

1. Fasten tap-winding connecting leads with cable shoes and M12 screws as

specified in the connection diagram provided (cable shoes and fastening
materials are not included in the delivery scope). The through-holes of the
connection contacts are horizontal as standard.

2. Make sure that the tap-winding connecting leads are not exerting any me-

chanical loads on the selector.

3. Take suitable measures to ensure that every screw connection cannot

come loose or settle (e.g. by using clamping washers). Attach the screen-
ing caps as shown in the illustration.

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands