MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 45 | Manualshive

Page: 45 / 256

background image

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

45

7545652/00 EN

VACUTAP

®

VR-Ex

5.3.1.2 Fastening oil compartment to transformer cover – separable on-load

tap-changer head

In on-load tap-changers with U

m

≥ 362 kV, you cannot lower the oil compart-

ment through the opening in the mounting flange from above, because the
diameter of the shielding rings is greater than the inner diameter of the
mounting flange. In this case, you must first lift the top part of the on-load
tap-changer head off of the bottom part and fasten the top part to the trans-
former cover. You can then fasten the oil compartment to the top part of the
on-load tap-changer head.

5.3.1.2.1 Lifting top part of on-load tap-changer head off supporting flange

(bottom part)

5.3.1.2.1.1 Removing on-load tap-changer head cover

NOTICE

Damage to the on-load tap-changer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer.

► Ensure that parts do not fall into the oil compartment.

► Check that all small parts are accounted for.

1.

CAUTION!

An unstably positioned oil compartment may tip over, re-

sulting in injuries or property damage. Place the oil compartment on a
level surface and secure it against tipping.

2. Remove red-colored packaging material and transport material from the

oil compartment.

3. Ensure that the inspection window is sealed off with the cover.

4. Remove the screws and washers from the on-load tap-changer head

cover.

Figure 21: On-load tap-changer head cover

«
...
43
44
45
46
47
...
»

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR-Ex

Brand: NARGESA Pages: 50

Brand: Idex Pages: 141

Brand: NTN Pages: 19

Brand: Danfoss Pages: 18

Brand: Koch Pages: 96

Brand: Giovenzana Pages: 46

Z100-H642.15 S11W2

Brand: Jäger Pages: 52

Brand: L&T Electrical & Automation Pages: 56

Brand: Exodraft Pages: 20

Brand: Unitary products group Pages: 12

Brand: Meritor Pages: 45

TERMALINE 8251 Series

Brand: BIRD Pages: 24

Jinsoku LE-1620

Brand: Genmitsu Pages: 29

Brand: Grizzly Pages: 24

CROUSE-HINDS Ex - d Series

Brand: Eaton Pages: 44

G3 Series EtherNet/IP

Brand: Numatics Pages: 154

AutoCut 5-32CTS

Brand: HYDROSCAND Pages: 64

Brand: hager Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands