manualshive.com logo in svg

CNC QB2, User Manual

Share
Download
CNC QB2 User Manual Download Page 1

 

Page 1 

 

 

QB2 CNC  

User guide 

 

 

 

Safety precautions 

Like any power tool, operating and using a CNC machine can be dangerous. Diligence must be applied when operating 

any machine. It is recommended to wear appropriate PPE such as eye protection and ear muffs for your own safety. 

NEVER leave a powered machine unattended at any time! 

In the event of an issue or if something doesn’t seem right, it is recommended to immediately disconnect power to 

the machine and unplug it from the wall power outlet. Contact our customer support team if you have any concerns 

about your machine. 

Always ensure your machine is free and clear of any swarf, dust or other obstructions that may impact the motion of 

your machine. We highly recommend the use of a Dust shoe and vacuum system for keeping your machine clean and 

clear of swarf and dust. 

Always ensure to follow the maintenance guide at the bottom of this manual after initial assembly and setup and also 

periodically to ensure your machine always performs to its optimal capacity. 

 

 

Summary of Contents for QB2






















Reviews:

No comments

Brands by name

Popular brands

Load more brands