manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

The MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual is a comprehensive guide for motorcycle enthusiasts. This invaluable manual covers everything from maintenance procedures to troubleshooting tips, ensuring that riders can keep their Stelvio 1200 running smoothly. Download this manual for free at manualshive.com and unleash the full potential of your bike.

Share
Download
background image

Rules

Safety rules

Carbon monoxide

If you need to keep the engine running while working on the vehicle, please ensure that you do so in

an open or very well ventilated area. Never run the engine in an enclosed area. If you do work in an

enclosed area, make sure to use a fume extraction system.

CAUTION

EXHAUST EMISSIONS CONTAIN CARBON MONOXIDE, A POISONOUS GAS WHICH CAN CAUSE
LOSS OF CONSCIOUSNESS AND EVEN DEATH.

Fuel

CAUTION

THE FUEL USED TO POWER INTERNAL COMBUSTION ENGINES IS HIGHLY FLAMMABLE AND
MAY BE EXPLOSIVE UNDER CERTAIN CONDITIONS. IT IS THEREFORE RECOMMENDED TO
CARRY OUT REFUELLING AND MAINTENANCE PROCEDURES IN A VENTILATED AREA WITH
THE ENGINE SWITCHED OFF. DO NOT SMOKE DURING REFUELLING AND NEAR FUEL VA-
POURS, AVOIDING ANY CONTACT WITH NAKED FLAMES, SPARKS OR OTHER SOURCES
WHICH MAY CAUSE THEM TO IGNITE OR EXPLODE.
DO NOT DISPERSE FUEL IN THE ENVIRONMENT.
KEEP OUT OF THE REACH OF CHILDREN

Hot components

The engine and the exhaust system components become very hot and remain hot for some time after

the engine has been switched off. When handling these components, wear insulating gloves or wait

until the engine and the exhaust system have cooled down.

Used engine oil and transmission oil

CAUTION

IT IS ADVISABLE TO WEAR PROTECTIVE IMPERMEABLE GLOVES WHEN SERVICING THE VE-
HICLE.
THE ENGINE OR GEARBOX OIL MAY CAUSE SERIOUS INJURIES TO THE SKIN IF HANDLED
FOR PROLONGED PERIODS OF TIME AND ON A REGULAR BASIS.
WASH YOUR HANDS CAREFULLY AFTER HANDLING OIL.
HAND THE OIL OVER TO OR HAVE IT COLLECTED BY THE NEAREST USED OIL RECYCLING
COMPANY OR THE SUPPLIER.
DO NOT DISPOSE OF OIL IN THE ENVIRONMENT
KEEP OUT OF THE REACH OF CHILDREN

Stelvio 1200 NTX MY11

Characteristics

CHAR - 7

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

Qingqi QM110GY Owner'S Manual preview
QM110GY
Brand: Qingqi Pages: 48
Graphite 56H820 Manual preview
56H820
Brand: Graphite Pages: 44
Coleman Powersports CT200U Owner'S Manual preview
Powersports CT200U
Brand: Coleman Pages: 37
Dakota Digital MCL-36K-TCH Installation Manual preview
MCL-36K-TCH
Brand: Dakota Digital Pages: 6
R&G LP0274BK Fitting Instructions Manual preview
LP0274BK
Brand: R&G Pages: 24
BMW Motorrad G 650 X Challenge 2006 Rider'S Manual preview
G 650 X Challenge 2006
Brand: BMW Motorrad Pages: 131
JIMS MILWAUKEE-EIGHT 5833 Instruction Sheet preview
MILWAUKEE-EIGHT 5833
Brand: JIMS Pages: 10
Crivit 303613 Instructions For Use Manual preview
303613
Brand: Crivit Pages: 58
PUIG 0295 Mounting Instructions preview
0295
Brand: PUIG Pages: 2
Yamaha XSR700M 2021 Owner'S Manual preview
XSR700M 2021
Brand: Yamaha Pages: 104
Yamaha Super Tenere ABS 2018 Owner'S Manual preview
Super Tenere ABS 2018
Brand: Yamaha Pages: 122
Yamaha XSR900P Owner'S Manual preview
XSR900P
Brand: Yamaha Pages: 124
Yamaha XTZ 125K Owner'S Manual preview
XTZ 125K
Brand: Yamaha Pages: 97
Yamaha YZFR6X(C) Owner'S Manual preview
YZFR6X(C)
Brand: Yamaha Pages: 120
KTM Power Parts 69029096140 Manual preview
69029096140
Brand: KTM Power Parts Pages: 12
Dayi Motor E-ODIN 2.0 Instructions Manual preview
E-ODIN 2.0
Brand: Dayi Motor Pages: 18
Tipperary Sportage How To Fit preview
Sportage
Brand: Tipperary Pages: 2
R&G LP0127BK Fitting Instructions Manual preview
LP0127BK
Brand: R&G Pages: 11

Brands by name

Popular brands

Load more brands