MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 114

Page: 114 / 385

1. Sensor (black wire)

2. Sensor signal - (grey wire)

3. Heater ground connection (white)

4. Heater power supply (white)

NAVIGATOR: PARAMETERS

Lambda probe

example value: 0 - 1000 mV

If there is a short circuit at + 5 V or above, the value read is approx. 5.000 mV. If there is a short circuit

to ground instead, the value read is equal to 0 mV and the Lambda Sensor Correction parameter shows

25%: no error is displayed, though.

Lambda sensor correction

example value: 1.00

In closed loop, the value must be close to 0 % (values not within the +10 % and -10 % range may

indicate a fault): In an open circuit, the lambda sensor signal is too low. Therefore, the control unit takes

it as a lean mixture condition and will try to enrich it. The value read will be +25%.

NAVIGATOR: STATUSES

Lambda check

Example value:

Open loop / Closed loop

Closed loop indicates that the control unit is using the lambda probe signal to keep the combustion as

close as possible to the stoichiometric value.

NAVIGATOR: ELECTRICAL ERRORS

Left lambda sensor P0130

- Shorted to positive.

Error cause

•

Excessive voltage (battery voltage) has been detected at PINS 32 and 22 of the BLUE

connector.

Troubleshooting

•

shorted to positive: with the key set to ON, disconnect the sensor connector and measure

voltage at PIN 1 on the cable harness side (white/yellow cable): if there is voltage (5 or 12

V), restore the cable harness; it there is no voltage, measure voltage at PIN 2, cable harness

side, (green/white cable) and if there is voltage, restore the cable harness; if there is no

voltage, replace the lambda sensor

Left lambda sensor heating P0135 -

shorted to positive / open circuit, shorted to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 11 of the BLUE connector.

•

If the circuit is open, shorted to negative: voltage equal to zero has been detected at PIN 11

of the BLUE connector.

Troubleshooting

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 114

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands