manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 108 / 385

Share
Download
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 108

Throttle position sensor

Function

In charge of telling the control unit the position of

the throttle valves.

Operation / Operating principle

The throttle valve position sensor works as a var-

iable resistance according to the throttle rotation.

Level in electrical circuit diagram:

Throttle and

idle motor

Location:

•

sensor: on the right cylinder throttle

body

•

connector: on the potentiometer

Electrical characteristics:

•

PINS A-C: throttle closed approx. 2.5

kOhm; throttle open approx. 1.5 kOhm.

•

PINS A-B: approx. 1.1 kOhm

Pin-out:

•

PIN A: ground connection

•

PIN B: supply v5V

•

PIN C: potentiometer signal

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: FUEL INJECTION SYSTEM

NAVIGATOR: PARAMETERS

Throttle

Example value:

 4.9°

NAVIGATOR: STATUSES

Throttle position

Example value:

Released/Pressed/Full load

Indicates if the throttle potentiometer is open or closed in the released position.

NAVIGATOR: ERRORS

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 108

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments