manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 162 / 385

Share
Download
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 162

Checking the desmodromic drum

Check gear drum for damage, scratches and wear

and replace the desmodromic control rod if nec-

essary.

Check the desmodromic segment «

3

» for damage

and wear and replace it if necessary.

Check the desmodromic bearing «

4

» for damage

and cracks and replace it if necessary.

Checking the forks

NOTE

THE FOLLOWING PROCEDURE IS VALID FOR ALL GEARBOX FORKS.

•

Check the transmission fork cam roller

«1» and the transmission fork tooth

«2» for damage, deformation and

wear.

•

Replace the transmission fork if nec-

essary.

•

Check the transmission fork move-

ment and if it is not regular, replace the

transmission forks.

See also

Disassembling the gearbox

Fitting the primary shaft

NOTE

TO REFIT, FOLLOW THE SAME INSTRUCTIONS AS FOR REMOVAL BUT IN REVERSE ORDER.
REMEMBER TO REPLACE ALL SEALING RINGS, CIRCLIPS AND SAFETY RINGS PREVIOUSLY
REMOVED.

See also

Removing the

Engine

Stelvio 1200 NTX MY11

ENG - 162

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments