MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 122

Page: 122 / 385

It this error persists, use a pressure gauge to check the pressure of the oil in the engine

circuit

Neutral sensor

Function

it tells the gear position to the control unit: in neutral or in gear.

Operation / Operating principle

for gear in neutral, the circuit is closed to ground connection: then, via CAN, the control unit sends the

signal to the instrument panel which turns on the neutral speed warning light.

Level in electrical circuit diagram:

start-up enabling switches

Location:

•

Sensor: rear / upper side of the gearbox

•

Connector: on the sensor

Electrical characteristics:

•

Gear in neutral: closed circuit (0 V on wire from control unit to sensor / switch in continuity).

•

Gearshift engaged: open circuit (12 V on wire from control unit to sensor / open switch,

infinite resistance)

Pin-out:

•

PIN 1: Voltage 12V

NAVIGATOR: STATUSES

Gear in neutral

Example value:

yes/no

DIAGNOSIS

•

Indication on the instrument panel always gear engaged: check the control unit connector

and the sensor connector: if they are not OK, restore the cable harness; if OK, disconnect

the connector and, with gear in neutral, check continuity to ground of the terminal, sensor

side: if there is not continuity, replace the sensor (after checking cable harness continuity

on the sensor side and the correct mechanical position); if there is, check cable continuity

between the sensor connector and PIN 23 of the BROWN connector: if there is no continuity,

restore the cable harness. If there is, replace the instrument panel if the vehicle performance

is correct (the engine starts with gear in neutral but the neutral warning light is off) or replace

the control unit if the vehicle performance is not correct (the engine does not start with gear

in neutral).

•

Indication on the instrument panel always gear in neutral: disconnect the terminals from the

sensor and check if there is continuity with ground connection at PIN toward the sensor, with

gear engaged: if there is continuity, replace the sensor. If it is ground insulated, it means

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 122

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands