MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 121

Page: 121 / 385

continuity, restore the cable harness; if there is cable continuity, with the key set to KEY ON,

check the cable ground insulation (from coil connector or control unit connector). If this is

not OK, restore the cable harness.

Engine oil pressure sensor

Function:

Indicates the instrument panel if there is

enough oil pressure (0.35 +/- 0.15 bar) (5.1 +/-

2.18 PSI) in the engine.

Operation / Operating principle:

normally closed

switch. With oil pressure above 0.35 +/-0.15 bar

(5.1 +/- 2.18 PSI), open circuit.

Level in wiring diagram:

fuel reserve and oil pres-

sure.

Location:

•

Sensor: in between the engine "V", a

little to the left, under the generator

•

Connector: on the sensor.

Pin-out

: Voltage 12V

Instrument panel

Oil sensor failure DSB 07

Error cause

•

An oil sensor failure is signalled when, with engine off, it is detected that the sensor circuit

is open. The test is performed only once when the key is set to ON. This error is signalled

by the bulb icon and the general warning light turns on as well.

Troubleshooting

•

Check the sensor connector and the instrument panel connector (PIN 17): If not OK, restore.

If OK, check the continuity of the purple cable between the sensor connector and the in-

strument panel connector PIN 17: if not OK, restore the cable harness; if OK, replace the

sensor.

Oil pressure failure DSB 08

Error cause

•

An oil sensor failure is signalled when, with engine running, it is detected that the sensor

circuit is closed. This error is signalled by the bulb icon and the general warning light turns

on as well.

Troubleshooting

•

Detach the sensor connector and check the purple cable is ground insulated: if there is

continuity to ground, restore the cable harness; if it is ground insulated, replace the switch.

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 121

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands