manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 353 / 385

Share
Download
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 353

BLEEDING SYSTEM WITH NAVIGATOR

This type of bleeding has to be carried out if after all the checks the brake lever and the pedal

are still spongy.

The operations described here are valid for both systems even though the description refers to

the front system.

FRONT

•

With Navigator properly connected, select the function "FRONT BRAKE BLEEDING PRO-

CEDURE".

•

The pump starts rotating.

•

While the pump is performing a rotation cycle, operate and release the front brake lever until

the message Navigator cycle completion is received.

•

This procedure allows the air to turn and to accumulate.

•

Once the procedure with Navigator is finished, perform the REGULAR BLEEDING to remove

the air from the system completely.

CAUTION

PERFORM THE REGULAR BRAKING SYSTEM BLEEDING, AS DESCRIBED AT THE END OF THE
CHAPTER.

See also

Front
Rear

Front

Any air trapped in the hydraulic circuit acts as a cushion, absorbing much of the pressure applied by

the brake pump and minimising the braking power of the calliper.

The presence of air is signalled by the "sponginess" of the brake control and by poor braking efficiency.

CAUTION

CONSIDERING THE DANGER FOR VEHICLE AND RIDER, IT IS STRICTLY NECESSARY, AFTER
REFITTING BRAKES AND RESTORING THE BRAKING SYSTEM TO THE REGULAR USE CON-
DITIONS, THAT THE HYDRAULIC CIRCUIT BE AIR PURGED.

NOTE

THE FOLLOWING OPERATIONS REFER TO ONLY ONE FRONT BRAKE CALLIPER BUT APPLY
TO BOTH CALLIPERS. THE VEHICLE MUST BE ON LEVEL GROUND TO BE PURGED. WHILE
PURGING THE HYDRAULIC SYSTEM, FILL THE RESERVOIR WITH THE NECESSARY QUANTITY
OF BRAKE FLUID. CHECK THAT, DURING THE OPERATION, THERE IS ALWAYS BRAKE FLUID
IN THE RESERVOIR.

REGULAR AIR BLEEDING SYSTEM

Stelvio 1200 NTX MY11

Braking system

BRAK SYS - 353

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments