MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 11

Page: 11 / 385

This number consists of numbers and letters, as in

the example shown below.

ZGULZG000YMXXXXXX

KEY:

ZGU

: WMI (World manufacturer identifier) code;

: model;

001

: version variation;

: free digit

year of manufacture

: production plant (M= Mandello del Lario);

XXXXXX

: serial number (6 digits);

CHASSIS NUMBER

The chassis number is stamped on the right hand

side of the headstock.

ENGINE NUMBER

The engine number is stamped on the left side,

close to the engine oil level check cap.

Dimensions and mass

WEIGHT AND DIMENSIONS

Specification

Desc./Quantity

Maximum width (without accessories)

2305 mm (90.75 in)

Maximum width at handlebar

956 mm (37.64 in)

Maximum width of vehicle with accessories

1080 mm (42.52 in)

Minimum / maximum height (adjustable windshield)

1436 / 1492 mm (56.53 / 58.74 in)

Saddle height

800 mm (31.5 in)

Minimum earth clearance

185 mm (7.3 in)

Wheelbase

1535 mm (60.43 in)

Kerb weight

281 kg (619.50 lb)

Kerb weight of full house vehicle

296 kg (652.57 lb)

Engine

NGINE

Specification

Desc./Quantity

Type

traverse-mounted twin-cylinder four-stroke V 90°

Cylinder number

Cylinder arrangement

V 90°

Stelvio 1200 NTX MY11

Characteristics

CHAR - 11

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 11 / 385

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews: