MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 127

Page: 127 / 385

upstream the resistance decreases, replace the instrument panel. If voltage continues to be

approximately 5V, restore the pink cable (there is a short circuit at + 5V).

Notes

If a short circuit to ground is detected at PIN 10 of the instrument panel connector, the display will show

a full scale air temperature indication of 60 °C (140 °F)

Check the ground insulation of the sensor connector pink cable: if there is a connection, restore the

cable harness; if it is earth insulated, check that sensor resistance is correct: if it is not OK, replace the

sensor; if it is OK, replace the instrument panel.

RUN/STOP switch

Function

It tells the control unit if the rider wishes to enable engine start-up or to keep the engine running.

Operation / Operating principle

If the driver wants to shut off the engine or to disable engine start-up, the switch should be open, i.e.

the Marelli control unit should not detect voltage at PIN 27 of the BLUE connector.

Level in electrical circuit diagram:

Start-up enabling switches.

Location:

•

right light switch.

•

connector: right side, near the coil.

Electrical characteristics:

•

STOP position: the circuit is open

•

RUN position: closed circuit (continuity)

PIN:

•

sky blue/orange cable: 0V if engine kill in STOP; 12V if engine kill in RUN

•

red/black cable: Voltage 12V

NAVIGATOR: STATUSES

Run / stop switch

Example value

:Run/Stop

DIAGNOSIS

•

Indication on Navigator always STOP: disconnect the connector and, with the switch set to

RUN, check if there is continuity towards the switch of both the green/orange and the grey/

yellow cables (sensor side): if there is not continuity, replace the sensor; if there is, check

the connector. If it is not OK, restore the cable harness; if it is OK, with the key set to ON,

check if there is voltage on the red/black cable (cable harness side): if there is no voltage,

restore the cable harness; if there is, check the ground insulation of the sky blue/orange

cable (cable harness side): if there is continuity to ground, restore the cable harness; if it is

OK, take the key to OFF and check that the BLUE connector is in good conditions and if

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 127

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands