manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 65 / 385

Share
Download
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 65

•

Operating from both sides, unscrew and remove both screws (1).

•

Remove the oil sump guard.

•

Place a container with +4,000 cm³ (244

cu in) capacity under the drainage plug

(3).

•

Unscrew and remove the drainage

plug (3).

•

Pull out the oil filler plug / engine oil

level dipstick (4).

•

Drain the oil into the container; allow

several minutes for oil to drain out com-

pletely.

•

Insert the oil filler plug / engine oil level

dipstick (4).

•

Check and if necessary, replace the

drainage plug (3) sealing washers.

•

Remove any metal deposits attached

to the drainage plug (3) magnet.

•

Screw and tighten the drainage plug

(3).

DO NOT DISPOSE OF OIL INTO THE ENVIRONMENT.
DISPOSE OF ENGINE OIL IN A SEALED CONTAINER AND
TAKE IT TO YOUR SUPPLIER OR TO THE NEAREST USED
OIL COLLECTION CENTRE.

Stelvio 1200 NTX MY11

Maintenance

MAIN - 65

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments