manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

The MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual is a comprehensive guide for motorcycle enthusiasts. This invaluable manual covers everything from maintenance procedures to troubleshooting tips, ensuring that riders can keep their Stelvio 1200 running smoothly. Download this manual for free at manualshive.com and unleash the full potential of your bike.

Share
Download
background image

Assembling the connecting rod

•

Lubricate the crankpin on which the

connecting rods are to be fixed.

•

If the connecting rods are not replaced,

be careful not to interchange the right

connecting rod with the left one and

vice versa.

To place the connecting rods: the two pins must

be facing the crankcase internal side.

•

Place the connecting rods and the

caps (B) on the crankshaft and fasten

them with new screws (A).

•

Remember these recommendations:

•

The screws fixing the connecting rods to the crankshaft must be replaced with new ones at

the following refitting as they are subject to high loads and stress;

•

The fitting clearance between bearing and connecting rod pin is 0.028 mm (0.0011 inch)

minimum and 0.052 mm (0.0020 inch) maximum;

•

The clearance between the shim washers of the connecting rod and those of the crankshaft

is comprised between 0.30 mm (0.01181 in) and 0.50 mm (0.01968 in);

•

Lock the screws (A) on the caps (B) with a torque wrench at the prescribed torque.

PAY ATTENTION TO CRANKSHAFT ROTATION WHEN ONLY THE CONNECTING RODS ARE
FITTED BECAUSE IT COULD HIT THE TWO LUBRICATION JETS INSIDE THE CRANKCASE.

Stelvio 1200 NTX MY11

Engine

ENG - 235

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

Sachs Bikes MadAss 50 Owner'S Manual preview
MadAss 50
Brand: Sachs Bikes Pages: 83
W-Tec Ondrejnik User Manual preview
Ondrejnik
Brand: W-Tec Pages: 6
KTM Freeride 350 AUS Setup Instructions preview
Freeride 350 AUS
Brand: KTM Pages: 25
R&G ECC0363R Fitting Instructions Manual preview
ECC0363R
Brand: R&G Pages: 6
hepco & becker 6536507 00 01 Mounting Instructions preview
6536507 00 01
Brand: hepco & becker Pages: 7
SHERCO XY 125 Owner'S Manual preview
XY 125
Brand: SHERCO Pages: 102
TVS WEGO 110 Fi Owner'S Manual preview
WEGO 110 Fi
Brand: TVS Pages: 60
Baja motorsports Dirt Runner 90 Owner'S Manual preview
Dirt Runner 90
Brand: Baja motorsports Pages: 66
hepco & becker 6504518 01 01 Manual preview
6504518 01 01
Brand: hepco & becker Pages: 5
hepco & becker 5049529 00 01 Quick Start Manual preview
5049529 00 01
Brand: hepco & becker Pages: 4
F4Customs Can-Am Spyder RT Quick Start Manual preview
Can-Am Spyder RT
Brand: F4Customs Pages: 3
O'Neal Dirt Manual preview
Dirt
Brand: O'Neal Pages: 28
N-Com B602 Quick Manual preview
B602
Brand: N-Com Pages: 14
KTM 60712933050 Information preview
60712933050
Brand: KTM Pages: 7
KTM 90.06.019.000 Mounting Instructions preview
90.06.019.000
Brand: KTM Pages: 2
KTM 45412955044S Fitting Instructions Manual preview
45412955044S
Brand: KTM Pages: 122
APRILIA QUASAR 100 Manual preview
QUASAR 100
Brand: APRILIA Pages: 256
Royal Enfield Bullet 350 2017 Manual preview
Bullet 350 2017
Brand: Royal Enfield Pages: 144

Brands by name

Popular brands

Load more brands